manualshive.com logo in svg

Analog Devices AD9361, Reference Manual

Share
Download
Analog Devices AD9361 Reference Manual Download Page 40

UG-570 

AD9361 Reference Manual 

 | Page 40 of 128 

SLOW ATTACK AGC MODE 

Slow attack mode is intended for slowly changing signals such as 
those found in some FDD applications, for example, WCDMA 
and FDD LTE. The slow attack AGC uses a second-order control 
loop with hysteresis that changes the gain to keep the average 
signal power within a programmable window. The power is 
measured between HB1 and the Rx FIR filter. This is the same 
location as the low power detector in Figure 18. In addition, the 
BBP can set bits to enable faster reactions for signals that exceed 
the LMT and ADC thresholds. Enable AGC slow attack mode 
with the ad9361_set_rx_gain_control_mode function. 
Figure 24 demonstrates the concept of the control loop. Where 
inner high threshold and inner low threshold are stored in 
negative dBFS. The outer high threshold and outer low threshold 
are stored as dB deltas to the inner thresholds. The A, B, C, and D 
step sizes are programmable. These step sizes determine how 
much the gain index pointer changes after the average signal 
power exceeds a threshold.  
Note that the 

AD9361

 does not have default thresholds or step 

sizes. The BBP must write all of these values using the 
ad9361_set_rx_gain_control_mode function. 

SLOW ATTACK AGC GAIN UPDATE TIME 

When the average signal power exceeds a threshold, the gain does 
not necessarily change immediately. In FDD systems, there are 
typically brief periods (such as those around slot boundaries) that 
accommodate gain changes or other system parameter updates. 
To accommodate this aspect of FDD protocols, the 

AD9361

 gain 

will only update after the gain update counter expires. The 
counter is clocked at the ClkRF rate (the input rate of the RFIR). 
The depth of the counter can be set equal to double or quadruple 
the value in these registers.  
The counter clock begins running three clock cycles after the 

AD9361

 enters the receive state. Since the BBP is responsible for 

moving the 

AD9361

 among its states, it can determine when the 

gain update counter will expire. In this way, the Gain Update 
Counter can be set such that it always expires at slot (or other) 
boundaries. Additionally the BBP can reset the gain update 
counter by setting the Enable Sync for Gain Counter bit and 
taking CTRL_IN2 high. 
The slow AGC is typically configured to have multiple power 
measurement cycles within each gain update period. The last 
power measurement performed before a gain update boundary 
determines whether (and by how much) the gain should change. 

Figure 24. Slow Attack AGC Control Loop Limits and Step Sizes 

DECREASE GAIN A STEPS

OUTER THRESHOLD HIGH

INNER THRESHOLD HIGH

INNER THRESHOLD LOW

OUTER THRESHOLD LOW

DECREASE GAIN B STEPS

INCREASE GAIN C STEPS

INCREASE GAIN D STEPS

NO GAIN CHANGE

EXAMPLE OF
AVERAGE
SIGNAL POWER

1

1668-

025

Rev. A

Summary of Contents for AD9361

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands