Allen-Bradley SMC-50 User Manual Download Page 192

Page: 192 / 292

192

Rockwell Automation Publication 1560F-UM001A-EN-P - June 2019

Chapter 10

Maintenance

PM Starts Protection—Fault and Alarm

PM Starts Fault (Code 51) and Alarm

You can configure the SMC-50 control module to provide a Fault and/or Alarm

to indicate that PM should be performed after a pre-defined number of starts

have occurred, Fault Code 51. Do this by using the PM Starts, Parameter 127,

Starts to PM, Parameter 22, and Meter Reset, Parameter 16.

The Starts to PM parameter indicates the number of starts before preventive

maintenance needs to be performed. This value counts down by one for each

start initiated, even if the start is not completed. When the Starts to PM value

reaches zero, the configured Fault and/or Alarm condition activates and the

counter stops counting.

After the preventive maintenance is complete, you can reset the Fault and/or

Alarm. You must reload the Starts to PM to the value configured and stored in

the PM Starts parameter through the Meter Reset, Parameter 16 via a HIM or

network communications.

The PM Starts Alarm function is enabled using the PM Starts bit in the Motor

Fault Enable, Parameter 230. The Alarm is enabled using the PM Starts bit in the

Motor Alarm Enable, Parameter 231.

Table 65 - Starts Protection Parameter List

Safety and Preventative

Maintenance

The Maintenance Technician should become familiar with the layout and be

aware of the basic system parameters. Only qualified technicians should be

allowed to work with this equipment under competent supervision.

General housekeeping is the key to maintaining power electronic and electrical

equipment. They are to be kept as dust free as possible. A scheduled program of

inspection will reduce the possibility of problems.

Parameter

Number

Parameter Name

(1)

(1) As displayed on the HIM or Connected Components Workbench configuration tools.

Minimum/Maximum

Value

Default

Value

Access

Units

127

PM Starts

1…50000

100

R/W

Starts to PM

0…50000

Meter Reset

Ready, Elapsed Time, Energy,

Time to PM, Starts to PM

Ready

R/W

ATTENTION:

Servicing energized industrial control equipment can be

hazardous. Severe injury or death can result from electrical shock, burn, or

unintended actuation of controlled equipment. Recommended practice is to
disconnnect and lock out control equipment from power sources, and allow any
stored energy in capacitors to dissipate. If it is necessary to work in the vicinity

of energized equipment, the safety related work practices of NFPA 70E,
Electrical Safety Requirements for Employee Workplaces, must be followed.

Summary of Contents for SMC-50





































































































































































































































































































Search results

Summary of Contents for SMC-50

Reviews:

Related manuals for SMC-50

Brands by name

Popular brands

Allen-Bradley SMC-50, User Manual

Search results

Summary of Contents for SMC-50

Reviews:

Related manuals for SMC-50

Brands by name

Popular brands