Alicat Scientific MC Series Installation & Maintenance Instructions Manual Download

Page: 24 / 103

COMPOSER

Composer

allows you to program

and save up to 20 custom gas mixes

containing 2 to 5 component gases

found in the gas lists (pages 40-47). The

minimum resolution is 0.01%.

Composer

is accessed by selecting

COMPOSER User Mixes

on the GAS

SELECT display.
Press SET when the arrow is aligned

with Add Mix.
Name the mix by pressing the UP and

DOWN buttons for letters, numerals

and symbols.

CHANGE CASE

– Toggles the letter

case. Letters remain in selected case

until CHANGE CASE is pushed again.
Press SET to save the name.
After naming the mix, press

ADD GAS

and select the gas category and the

component gas.
Select the digit with arrow and adjust

the % with the UP and DOWN buttons.

Press set to save. Add up to 4 more

gases as needed. The total must equal

100% or an error message will appear.

GAS OPTNS

allows you to adjust the

percentage of the constituents or

delete a gas from the mix. Gas mixes

cannot be adjusted after they have

been saved.

DOWN

CANCEL

SET

>Add Mix: 20 Free

DOWN

BACK/

CANCEL

CHANGE

CASE

SET

LETTER

COMPOSER Mix name:

MyGas
------

ADD GAS

BACK/

CANCEL

CHANGE

CASE

SET

GAS

OPTNS

COMPOSER Mix: MyGAS

0.00% of Total

EDIT

NAME

Summary of Contents for MC Series








































































































Search results

Summary of Contents for MC Series

Reviews:

Related manuals for MC Series

Brands by name

Popular brands

Alicat Scientific MC Series, Installation & Maintenance Instructions Manual

Search results

Summary of Contents for MC Series

Reviews:

Related manuals for MC Series

Brands by name

Popular brands