Alicat Scientific MC Series Installation & Maintenance Instructions Manual Download

Page: 74 / 103

Technical Data for MCP Moderate Flow Mass Flow Controllers

0 to 50 slpm Full Scale through 0 to 250 slpm Full Scale

Alicat MCP

mass flow controllers are fitted with a high performance valve for low pressure applications.

The following specifications are applicable to Alicat MCP-Series Mass Flow Controllers only.

Please Note Maximum Pressure of 80 psig.

Standard Operating Specifications (Contact Alicat for available options)

Performance

MCP Mass Flow Controller

Accuracy at calibration conditions

after tare

± (0.8% of R 0.2% of Full Scale)

High Accuracy at calibration conditions

after tare

± (0.4% of R 0.2% of Full Scale)

Repeatability

± 0.2% Full Scale

Zero Shift and Span Shift

0.02% Full Scale / ºCelsius / Atm

Operating Range / Turndown Ratio

0.5% to 100% Full Scale / 200:1 Turndown

Maximum Controllable Flow Rate

102.4% Full Scale

Typical Response Time

100 ms (Adjustable)

Warm-up Time

< 1 Second

Communications / Power

MCP Mass Flow Controller

Monochrome LCD or Color TFT

Display with integrated touchpad

Simultaneously displays Mass Flow, Volumetric Flow, Pressure and Temperature

Digital Input/Output Signal

Options

RS-232 Serial / RS-485 Serial / Modbus / PROFIBUS

Analog Input/Output Signal

Options

0-5 Vdc / 1-5 Vdc / 0-10 Vdc / 4-20 mA

Optional Secondary Analog

Input/Output Signal

0-5 Vdc / 1-5 Vdc / 0-10 Vdc / 4-20 mA

Electrical Connection Options

8 Pin Mini-DIN / 9-pin D-sub (DB9) / 15-pin D-sub (DB15) / 6 pin locking

Supply Voltage

12 to 30 Vdc (15-30 Vdc for 4-20 mA outputs)

Supply Current

0.250 Amp

1. The

Digital Output Signal

communicates Mass Flow, Volumetric Flow, Pressure and Temperature

2. The

Analog Output Signal

and

Optional Secondary Analog Output Signal

communicate your choice of Mass

Flow, Volumetric Flow, Pressure or Temperature

3. If selecting PROFIBUS, no analog signal is available. See PROFIBUS specifications for supply voltages and

currents

(

www.alicat.com/profibus

). PROFIBUS units do not have the display.

Operating Conditions

MCP Mass Flow Controller

Mass Reference Conditions (STP)

25ºC & 14.696 psia (standard — others available on request)

Operating Temperature

−10 to +50 ºCelsius

Humidity Range

(Non–Condensing)

0 to 100%

Max. Internal Pressure (Static)

80 psig

Proof Pressure

175 psig

Mounting Attitude Sensitivity

None

Valve Type

Normally Closed

Ingress Protection

IP40

Wetted Materials

303 & 302 Stainless Steel, Viton®, Heat Cured Silicone Rubber, Glass Reinforced

Polyphenylene Sulfide, Heat Cured Epoxy, Aluminum, Gold, Brass, 430FR Stainless

Steel, Silicon, Glass.

If your application demands a different material, please contact Alicat.

Range Specific Specifications

Full Scale Flow Mass

Controller

Pressure Drop

at FS Flow

(psid) venting to atmosphere

Mechanical

Dimensions

Process Connections

MCP

50 slpm

4.4”H x 5.4”W x 1.6”D

1/4” NPT Female

MCP

100 slpm

MCP

250 slpm

5.0”H x 6.3”W x 1.6”D

1/2” NPT Female

1. Lower Pressure Drops Available, please see our

WHISPER-Series

mass flow controllers at

www.alicat.com/whisper

2. Compatible with Swagelok® tube, Parker®, face seal, push connect and compression adapter fittings. VCR and SAE

connections upon request.

Summary of Contents for MC Series








































































































Search results

Summary of Contents for MC Series

Reviews:

Related manuals for MC Series

Brands by name

Popular brands

Alicat Scientific MC Series, Installation & Maintenance Instructions Manual

Search results

Summary of Contents for MC Series

Reviews:

Related manuals for MC Series

Brands by name

Popular brands