Alicat Scientific MC Series Installation & Maintenance Instructions Manual Download

Page: 84 / 103

Specification

Meter or

Gauge

Small Valve

Controller

Large Valve

Controller

Description

Input /Output Signal Digital

PROFIBUS DP

Electrical Connections

DB9

Supply Voltage:

7 to 30 Vdc

12 to 30 Vdc

24 to 30 Vdc

Supply Current

80mA @ 12Vdc

65mA @ 24Vdc

295mA @ 12Vdc

280mA @ 24Vdc

780mA @ 24Vdc

Technical Data for

PROFIBUS

Meters, Gauges and Controllers

NOTICE:

The following specifications are applicable to Alicat PROFIBUS enabled meters,

gauges and controllers only.

All other operating specifications are shown in the Technical Data page for standard Alicat

instruments.
All standard device features and functions are available and operate in accordance with the

standard Alicat Scientific device operating manual provided with the device.

Power and Signal Connections:

Connect to the device using two DB9 connectors.
The female top connection is PROFIBUS.
The male connection on the side is power and

RS-232 or RS-485.
Pin out diagrams for all PROFIBUS enabled

Alicat devices are shown:

PROFIBUS MC1SLPM shown to provide PROFIBUS connector dimensions only. Flow body and valve

dimensions will vary with range. Please see Alicat’s device specifications for complete dimensions.

PROFIBUS units do not have a display screen.

2 x 8-32 UNC

┬v

.350

.525

.35

4.26

4.08

3.76

3.59

1/8 NPT

Both Sides

1.05

.525

.35

2.225

.150

.125

.925

MC-1SLPM-PROFIBUS

1. NC

2. OPT GND

3. DP

4. RTS

5. DGD

6. VP

7. OPT 7 to 30VDC

8. DN

9. NC

TOP

1. NC

2. RS232RX

3. RS232TX

4. NC

5. GND

6. NC

7. 7 to 30VDC

8. GND

9. NC

SIDE

Summary of Contents for MC Series








































































































Search results

Summary of Contents for MC Series

Reviews:

Related manuals for MC Series

Brands by name

Popular brands

Alicat Scientific MC Series, Installation & Maintenance Instructions Manual

Search results

Summary of Contents for MC Series

Reviews:

Related manuals for MC Series

Brands by name

Popular brands