Alicat Scientific MC Series Installation & Maintenance Instructions Manual Download

Page: 26 / 103

COMMUNICATION SELECT

Access

Communication Select

by pressing

the button above

RS232 COMM

RS485

COMM

on the

Select Menu

display.

Unit ID

– Valid unit identifiers are the

letters A-Z and @. The identifier allows

you to assign a unique address to each

device so that multiple units can be

connected to a single RS-232 or RS-485

computer port.
Press

UNIT ID

. Use the UP and DOWN

buttons to change the Unit ID. Press SET to

record the ID. Press Reset to return to the

previously recorded Unit ID.

Any Unit ID change will take effect when

Communication Select is exited

If the symbol @ is selected as the Unit

ID, the device will enter streaming mode

when Communication Select is exited.

See RS-232 Communications (page 33) for

information about the streaming mode.

Baud

– Both this instrument and your

computer must send/receive data at the

same baud rate. The default baud rate for

this device is 19200 baud.
Press

BAUD

. Use the UP and DOWN

buttons

to select the baud rate that

matches your computer. The choices are

38400, 19200, 9600, or 2400 baud. Press

SET to record the baud rate.

Any baud rate change will not take effect

until power to the unit is cycled.

BACK

RESET A

SET

UNIT ID

DOWN

BACK

SET

BAUD

19200

BACK

MAIN

UNIT ID

BAUD

19200

Summary of Contents for MC Series








































































































Search results

Summary of Contents for MC Series

Reviews:

Related manuals for MC Series

Brands by name

Popular brands

Alicat Scientific MC Series, Installation & Maintenance Instructions Manual

Search results

Summary of Contents for MC Series

Reviews:

Related manuals for MC Series

Brands by name

Popular brands