Alcatel-Lucent OmniTouch Administration Manual Download Page 213 | Manualshive

Page: 213 / 382

background image

To generate a call report for a particular user

Provisioning and Account Management

............................................................................................................................................................................................................................................................

8AL90208USAD ed01
November 20, 2008

4 - 4 5

............................................................................................................................................................................................................................................................

Project Code

A text string needed to schedule a conference.
(may be used for billing purposes)

Call ID

Internal, unique ID for a specific call.

•

Ad Hoc call

:

Each call generates a new

Call ID.

•

Scheduled and Reservationless
Conference calls

:

Use same Call ID for

each access.

Note:

Call IDs must not contain the

@

character.

Called Number

Incoming number dialed by user (DNIS: Dialed
Number Identification Service). Typically used
by Call Centers with different numbers for
different services.

Server

In a single server configuration, the server name
will be the same on multiple calls; in a multi-
server configuration, the server name may be
different on multiple calls. (useful for
troubleshooting)

Trunk Number

Only appears for systems with built-in gateway
cards. (0-7)

Channel Number

Derived from a particular trunk; reported by the
Gateway card.
The number of actual channels per trunk is as
follows:

•

T1 with PRI signaling

– 23

•

T1 with CAS

– 24 (

Note that Direct

Inward Dialing, DID, is supported.

)

•

E1 with PRI

– 30

Leg Call ID

Call ID of an audio leg for VoIP or call ID of part
of application sharing session if Leg Type is
AppShare or call ID of part of video session if
Leg Type is Video.

Leg Type

Audio, Application Sharing, or Video.

«
...
211
212
213
214
215
...
»

Summary of Contents for OmniTouch































































































































































































































































































































































































Reviews:

No comments

Related manuals for OmniTouch

Brand: Native Instruments Pages: 74

AltiWare OE 4.6

Brand: Altigen Pages: 518

OneVision DEFINITY G3 Fault Management and integration

Brand: AT&T Pages: 153

WiFi-Doc Client for iOS

Brand: Mitsubishi Pages: 10

Brand: Brother Pages: 24

MacBroidery„ Embroidery Lettering Software for Mac

Brand: Brother Pages: 56

Brand: Brother Pages: 48

Brand: Brother Pages: 272

Brand: Brother Pages: 200

ANTI-VIRUS 2011 - REV 2011.07

Brand: AVG Pages: 210

ANTI-VIRUS 2011 - REV 2011.06

Brand: AVG Pages: 210

Brand: Vonamic Pages: 30

ALTIRIS DEPLOYMENT SOLUTION 7.1 - FOR DELL SERVERS V1.0

Brand: Symantec Pages: 47

PC ANYWHERE SOLUTION V 12.5

Brand: Symantec Pages: 63

Active Management Technology v5.0

Brand: Intel Pages: 143

Brand: FieldServer Pages: 19

DVDMovieFactory

Brand: Ulead Pages: 50

VIAVOICE-SIMPLY DICTATION FOR MAC OS X

Brand: IBM Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands