Alcatel-Lucent OmniTouch Administration Manual Download Page 51 | Manualshive

Page: 51 / 382

background image

SIP proxies (VoIP configuration)

System Configuration

............................................................................................................................................................................................................................................................

8AL90208USAD ed01
November 20, 2008

2 - 3 1

............................................................................................................................................................................................................................................................

The following entries will be site- and installation-specific. Contact your customer support
representative for more information regarding your particular installation.

Table 2-7

Default Outbound SIP Proxy Fields

OXE 9.0 Spatial Redundancy Mode

Check this box if you are using an Alcatel-
Lucent OmniPCX 9.0 as your proxy server. The
following screen shows the fields that are
displayed if

OXE 9.0 Spatial Redundancy

Mode

is enabled for the default outbound SIP

proxy.

Figure 2-13

Outbound OXE 9.0 Spatial Redundancy Mode

Default Outbound Proxy (Port)

If specified, all SIP invites will first go to this IP
address (When OXE 9.0 Spatial Redundancy
Mode is enabled, this can only be a name). If
other realms are specified, this address will be
overridden. (Port number associated with the
Default Outbound Proxy.)

DNS Server

(Only appears if OXE 9.0 Spatial Redundancy
Mode is enabled.)

This is the IP Address of the primary OXE 9.0
server.

Alternate DNS Server

(Only appears if OXE 9.0 Spatial Redundancy
Mode is enabled.)

This is the IP Address of the secondary OXE 9.0
server.

Alternate Outbound Proxy (Port)

(Appears if OXE 9.0 Spatial Redundancy Mode
is

NOT

enabled.)

If specified, all SIP invites will go to this IP
address (or name) if the Default Outbound
Proxy is unavailable. (Port number associated
with the Alternate Outbound Proxy.)

Failover Timeout (Seconds)

(Appears if OXE 9.0 Spatial Redundancy Mode
is

NOT

enabled.)

If the Default Outbound Proxy cannot be
contacted within this amount of time (in
seconds), the Alternate Outbound Proxy is
contacted.

«
...
49
50
51
52
53
...
»

Summary of Contents for OmniTouch































































































































































































































































































































































































Reviews:

No comments

Related manuals for OmniTouch

EOS-1D Mark II Digial

Brand: Canon Pages: 2

Brand: Adobe Pages: 122

GigaStudio 3.04

Brand: Tascam Pages: 2

APPLICATION STACK 1.3 RELEASE

Brand: Red Hat Pages: 26

ANTI-VIRUS - FOR MICROSOFT EXCHANGE

Brand: F-SECURE Pages: 115

High Performance Storage System HPSS

Brand: IBM Pages: 311

Symposium TAPI Service Provider for Succession 3.0

Brand: Nortel Pages: 198

PERFORMANCE MANAGEMENT FOR POWER SYSTEMS - INTERACTIVE GRAPHING SUPPORT FOR ...

Brand: IBM Pages: 29

Brand: HP Pages: 210

Brand: HP Pages: 3

D300s - Evo - 128 MB RAM

Brand: HP Pages: 2

ProBook 4525s - Notebook PC

Brand: HP Pages: 4

ProBook 4525s - Notebook PC

Brand: HP Pages: 149

Powershot SX20 IS

Brand: Canon Pages: 44

Brand: Canon Pages: 40

Brand: Canon Pages: 46

Brand: Canon Pages: 157

Networked Multi-Projection

Brand: Canon Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands