Alcatel-Lucent OmniTouch Administration Manual Download Page 160 | Manualshive

Page: 160 / 382

background image

............................................................................................................................................................................................................................................................

To install the standalone server

Management Actions

3 - 2 2

8AL90208USAD ed01

November 20, 2008

............................................................................................................................................................................................................................................................

To install the standalone server

........................................................................................................................................................................................................................

1

Replace the old server with the new server.

........................................................................................................................................................................................................................

2

Scratch install the new server to the same software revision as the one used for the most
recent backup. (Refer to the

My Teamwork Unified Conferencing and Collaboration

Application Installation Guide

for installation procedures.)

........................................................................................................................................................

E

N D

O

F

S

T E P S

To restore configuration settings on the new server

........................................................................................................................................................................................................................

1

After the installation of the server is complete and server reboots, log into the Serial
Administration console:

Username: admin

Password: changeme

Figure 3-13

Serial Console

........................................................................................................................................................................................................................

2

Configure any required networking information.

a. Select

Networking Configuration

.

«
...
158
159
160
161
162
...
»

Summary of Contents for OmniTouch































































































































































































































































































































































































Reviews:

No comments

Related manuals for OmniTouch

Brand: Cabletron Systems Pages: 16

Brand: CSSN Pages: 8

Mobile Anti-Virus 60 Series

Brand: F-SECURE Pages: 90

MOBILE SECURITY 2010 FOR ANDROID

Brand: F-SECURE Pages: 20

VIRUSSCAN HOME EDITION 7.0

Brand: McAfee Pages: 56

APPLICATION STACK 1.1 RELEASE

Brand: Red Hat Pages: 30

Brand: Juniper Pages: 9

Brand: Xils lab Pages: 46

DirectRoute 3.0

Brand: Magellan Pages: 108

VIAVOICE 10-PRO USB EDITION

Brand: IBM Pages: 160

ACCULINK 7800-D1-999

Brand: Paradyne Pages: 11

Brand: Focusrite Pages: 22

ASSIMILATOR KONNEKT

Brand: TC Electronic Pages: 18

MultiRack SoundGrid V9.7

Brand: Waves Pages: 39

MultiRack SoundGrid V9.5

Brand: Waves Pages: 35

Brand: Patton electronics Pages: 331

Brand: Brother Pages: 16

Brand: Brother Pages: 361

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands