AJA Io IP Installation And Operation Manual Download Page 77

Page: 77 / 86

Io IP Transport, Capture, Display v16.2r1 77 www.aja.com

Korea KCC Compliance Statement

ꩡ

끞

녅

껽

驩

ꓭ

넩

韥韥鱉

꽺ꓩ끞

쀍陲꾅꫑

ꩡ끞뼕

ꑞ놶냱ꈑ

놶뼞ꫦ뵾閵ꌱ

ꗐ냵

韥韥ꈑ꫑

閵뇊

끞

쀍陲꾅꫑

ꩡ끞뼍鱉

陲끥

놹볁閹ꫢ넍

끥ꇙ閵

넽걪鱽鲙

Taiwan Compliance Statement

This is a Class A product based on the standard of the Bureau of Standards,

Metrology and Inspection (BSMI) CNS 13438, Class A. In a domestic environment

this product may cause radio interference in which case the user may be required

to take adequate measures.

Japan Compliance Statement

This is a Class A product based on the standard of the VCCI Council (VCCI 32: 2016).

If this equipment is used in a domestic environment, radio interference may

occur, in which case, the user may be required to take corrective actions.

China Compliance Statement

This product has been tested to the following Chinese standards:
GB/T13837-2012, GB17625.1-2012 and GB8898-2011
This product meets the requirements of implementation rules for compulsory

certification (REFNO.CNCA-C08-01:2014) under certificate number

2018010805038172.

Translated Warning and Caution Messages

The following caution statements, warning conventions, and warning messages

apply to this product and manual.

Summary of Contents for Io IP























































































Search results

Summary of Contents for Io IP

Reviews:

Related manuals for Io IP

Brands by name

Popular brands

AJA Io IP, Installation And Operation Manual

Search results

Summary of Contents for Io IP

Reviews:

Related manuals for Io IP

Brands by name

Popular brands