background image

Io IP Transport, Capture, Display v16.2r1 82 www.aja.com

 

Warning! Since the Mains plug is used as the disconnection for the device, it must 

remain readily accessible and operable.

Avertissement! Puisque la prise principale est utilisée pour débrancher l'appareil, 

elle doit rester aisément accessible et fonctionnelle.

Warnung! Da der Netzstecker als Trennvorrichtung dient, muss er stets zugänglich 

und funktionsfähig sein.

¡Advertencia! Puesto que el enchufe de la red eléctrica se utiliza como dispositivo 

de desconexión, debe seguir siendo fácilmente accesible y operable.

Aviso! Dado que a ficha principal é utilizada como a desconexão para o dispositivo, 

esta deve manter-se prontamente acessível e funcional.

Avviso! Poiché il cavo di alimentazione viene usato come dispositivo di 

sconnessione, deve rimane prontamente accessibile e operabile.

Warning! Protect the power cord from being walked on or pinched particularly at 

plugs, convenience receptacles, and the point where they exit from the device.

Avertissement! Protégez le cordon d'alimentation pour que l'on ne marche 

pas dessus ou qu'on le pince, en particulier au niveau des prises mâles, des 

réceptacles de convenance, et à l'endroit où il sort de l'appareil.

Warnung! Vermeiden Sie, dass auf das Netzkabel getreten oder das Kabel geknickt 

wird, insbesondere an den Steckern, den Steckdosen und am Kabelausgang am 

Gerät.

¡Advertencia! Proteja el cable de energía para que no se le pise ni apriete, en 

especial cerca del enchufe, los receptáculos de conveniencia y el punto del que 

salen del equipo.

Aviso! Proteja o cabo de alimentação de ser pisado ou de ser comprimido 

particularmente nas fichas, em tomadas de parede de conveniência e no ponto 

de onde sai do dispositivo.

Avviso! Proteggere il cavo di alimentazione in modo che nessuno ci cammini sopra 

e che non venga schiacciato soprattutto in corrispondenza delle spine e del 

punto in cui esce dal dispositivo. 

Summary of Contents for Io IP























































































Reviews: