AJA Io IP Installation And Operation Manual Download Page 3

Page: 3 / 86

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Contacting AJA Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 1 – Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Io IP Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

AJA Software & Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Network Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Disk Storage Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

About Io IP Modal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

s2110 Firmware: 10-bit, 4:2:2, YCbCr . . . . . . . . . . . . . . . . . . . . . . . . . 10
s2110-RGB Firmware: 12-bit, 4:4:4, RGB . . . . . . . . . . . . . . . . . . . . . . . 10
s2022 Firmware: 10-bit, 4:2:2, YCbCr . . . . . . . . . . . . . . . . . . . . . . . . . 11

Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Front Panel Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . 12
Rear Panel Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Bottom Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

In This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Chapter 2 – Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Shipping Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Installing Io IP Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

NMOS Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
macOS Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Io IP Firmware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Cabling the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Io IP Cable Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Unicast and Multicast Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Chapter 3 – Io IP Operation. . . . . . . . . . . . . . . . . . . . . . . . . 19

Using Io IP with Professional Video /Audio Software . . . . . . . . . . . . . . . . 19

Capture Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

AJA Control Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Control Panel Operation in ST 2022-6 Mode . . . . . . . . . . . . . . . . . . . . . 27

Contents

Summary of Contents for Io IP























































































Search results

Summary of Contents for Io IP

Reviews:

Related manuals for Io IP

Brands by name

Popular brands

AJA Io IP, Installation And Operation Manual

Search results

Summary of Contents for Io IP

Reviews:

Related manuals for Io IP

Brands by name

Popular brands