AJA Io IP Installation And Operation Manual Download Page 73 | Manualshive

Page: 73 / 86

background image

Io IP Transport, Capture, Display v16.2r1 73 www.aja.com

Audio Output Digital

• 16-channel, 24-bit SDI embedded audio, 48 kHz sample rate, synchronous
• 8-channel HDMI embedded audio, 48 kHz sample rate, synchronous

Audio Outputs Analog

• 8-channel, 24-bit D/A analog audio, 48 kHz sample rate, balanced, using

industry standard 8x XLR on DB-25 breakout cable (cable not included)

•  +24 dBu full scale digital (0 dBFS)
•  +/- 0.2 dB 20 to 20 kHz frequency response
•  Output supported across Ch 1-8, Ch 1-4, or Ch 5-8 depending on the chosen

configuration

Downstream Keyer

• Supports graphics up to 2K/HD with alpha channel over video, matte or

framebuffer, or framebuffer content over incoming video or matte

Reference and LTC I/O

• 1x BNC assignable to Reference video or LTC input

Reference

•  Analog Color Black (1V) or Composite Sync (2 or 4V) or HD Tri-Level Sync (1V)
•  Reference input is terminated into 75 ohms when Genlock is set to Ref In
•  Applicable in SMPTE ST 2022-6/7 environments

Discovery, Registration and Control

• NMOS Tx/Rx support for SMPTE ST 2110 according to standards IS-04 v1.3 and

IS-05 v1.1
• Applicable in SMPTE ST 2110 environments

• LLDP

IP Clock

• PTP support compliant with PTP PTPv2 / IEEE 1588-2008
• Applicable in SMPTE ST 2110 environments

Electrical Interface

• Thunderbolt 3 (2x)

Size (w x d x h)

• 8.74” x 8.11” x 1.65” (222.0 x 206.0 x 41.9 mm)

Weight

• 3.3 lbs (1.5 kg)

Power (device only)

• 10-20V, 33W typical, 38W max, 72W max with USB-C power delivery to

external devices

Environment

•  Safe Operating Temperature Range: 0 to 40 C (32 to 104 F)
•  Safe Storage Temperature (Power OFF): -40 to 60 C (-40 to 140 F)
•  Operating Relative Humidity: 10-90% noncondensing
•  Operating Altitude: <3,000 meters (<10,000 feet)

«
...
71
72
73
74
75
...
»

Summary of Contents for Io IP























































































Reviews:

No comments

Related manuals for Io IP

AF-600 FP Series

Brand: GE Pages: 7

Brand: Zmotion Pages: 48

Brand: V-Tec Pages: 16

Brand: Perma Pages: 26

Star SuperNova S126

Brand: Tyco Fire Product Pages: 4

Brand: Atlas Copco Pages: 116

Panacom PANAIP7GM

Brand: PSA Pages: 10

Brand: Commax Pages: 11

Brand: Euroscreen Pages: 39

PATRIOT-AT F-12PPL-HD-AT1

Brand: Aqua Creek Products Pages: 21

Brand: Fender Pages: 51

Brand: ICP DAS USA Pages: 4

Brand: IDEAL Pages: 68

Brand: M-system Pages: 3

Brand: ION Pages: 16

Brand: Carel Pages: 94

Brand: Digital Flash Memory Pages: 10

Brand: Comelit Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands