AJA Io IP Installation And Operation Manual Download Page 5

Page: 5 / 86

Io IP Transport, Capture, Display v16.2r1 5

www.aja.com

Chapter 1 – Introduction

Overview

Io IP is a powerful yet portable video and audio I/O device for professional IP

based workflows. As part of AJA’s industry-leading Io line of Thunderbolt capture

and playback devices, Io IP works seamlessly with a large number of popular

creative software applications, including out-of-the-box support for Adobe

Premiere Pro, Apple FCP, and Avid Media Composer.
Designed as a flexible platform with support for SMPTE ST 2022-6 and ST 2110

uncompressed IP video/audio, Io IP brings the highest quality 2K, HD, and SD

video and audio over IP to computers running Mac or Windows Operating

Systems. Io IP can also support 4K/UltraHD p60 (2SI) capture or playback, via

SMPTE ST 2110-23.
Io IP is also supported through the very same SDK as the rest of the KONA family,

making it straight forward for developers to make the transition to Video over IP.

Io IP Features

Io IP is designed as a platform with the flexibility to support different

uncompressed IP requirements at the highest quality for 4K/UltraHD, 2K/HD, SD

video and audio over IP for host systems running Mac or Windows Operating

Systems. By loading the appropriate firmware (aka bitfile), Io IP is able to change

its 'personality' to fit the required workflow as follows.
s2022 firmware supports Rx and Tx for:

• YCbCr 4:2:2 10-bit for 2K/HD and SD.
• Supports 2022-7 for redundant Tx.

s2110 firmware supports Rx and Tx for:

•  YCbCr 4:2:2 10-bit for 4K/UltraHD, 2K/HD and SD.
•  Supports 2022-7 for redundant Tx up to 2K/HD.
•  Supports 2110-23 can be used for 4K/UltraHD p60 (2SI) capture or playback.

s2110-RGB firmware supports Tx for:

• RGB 4:4:4 12-bit for 2K/HD post production rates (23, 24, 25)
• Supports 2022-7 for redundant Tx up to 2K/HD.

NOTE: NDI is supported on Io IP in the same way as it is supported on KONA 4, courtesy

of running Newtek Connect.

Summary of Contents for Io IP























































































Search results

Summary of Contents for Io IP

Reviews:

Related manuals for Io IP

Brands by name

Popular brands

AJA Io IP, Installation And Operation Manual

Search results

Summary of Contents for Io IP

Reviews:

Related manuals for Io IP

Brands by name

Popular brands