AJA Io IP Installation And Operation Manual Download Page 66

Page: 66 / 86

Io IP Transport, Capture, Display v16.2r1 66 www.aja.com

Figure 15. Transmit Redundancy Settings

UltraHD Configuration

To send/ receive 4K/UltraHD over IP:
1.  Be sure to have SFP2 connected as well as SFP1.
2.  Use Generate or Manually configure IP settings.
3.  Uncheck Follow Input (on Receiver).
4.  Manually set frame buffer to desired 4K/UltraHD format.

4K/UltraHD Configuration (2110)

To setup UltraHD or 4K operation start by using the Generate feature in the

advanced tab of the IP config from Control Panel. This will enumerate the IP

settings to allow basic operation over IP. This is a good starting point for all

configurations. Be sure to have both SFP 1 and SFP 2 connected as 4K/UltraHD

will require the use of it. If you are sending between the AJA devices such as a

KONA IP and Io IP, inversely set the Rx Destination Address and the Tx Remote

between the two devices.
If the Io IP is going to be used for transmitting the signal, once the Tx Remote

parameters are set and generated, setup to playback 4K/UltraHD signal through,

test pattern of control panel, control room or other AJA compatible video

playback software (ex Media Composer, Premiere, etc).

Summary of Contents for Io IP























































































Search results

Summary of Contents for Io IP

Reviews:

Related manuals for Io IP

Brands by name

Popular brands

AJA Io IP, Installation And Operation Manual

Search results

Summary of Contents for Io IP

Reviews:

Related manuals for Io IP

Brands by name

Popular brands