AJA Io IP Installation And Operation Manual Download Page 36

Page: 36 / 86

Io IP Transport, Capture, Display v16.2r1 36 www.aja.com

Video Setup Screen

The Video Setup screen shows various other settings which will affect how

video inputs and outputs behave, and how Io IP interacts with some software

applications.

Video Setup

Progressive Pref

Allows you to choose to prefer p (progressive frames) or PsF (progressive

segmented frames) on non-interlaced output. This feature is used to default the

hardware to use either p or PsF output over SDI when it has not been specified by

the application.

Color Space

Sets the video color space. Select from:

•  Auto
•  Rec 601
•  Rec 709

Gamma

Sets the video gamma. Intended for use with legacy Apple displays. Select from:

• Auto
• Gamma 1.8

VANC Checkbox (inactive on Io IP)

This checkbox enables the tall frame buffers that include VANC, which is not

supported by Io IP. When using SMPTE ST 2110 the video flow is the video raster

only. VANC/HANC is sent on a separate IP flow, along with audio. ST 2110 is

designed to support separate essence flows for each data type.

Summary of Contents for Io IP























































































Search results

Summary of Contents for Io IP

Reviews:

Related manuals for Io IP

Brands by name

Popular brands

AJA Io IP, Installation And Operation Manual

Search results

Summary of Contents for Io IP

Reviews:

Related manuals for Io IP

Brands by name

Popular brands