Agilent Technologies E8362C Service Manual Download Page 336

Page: 336 / 382

7-80

Service Guide E8364-90038

Repair and Replacement Procedures

PNA Series Microwave Network Analyzers

Removing and Replacing the Lithium Battery

E8362C, E8363C, E8364C

Removing and Replacing the Lithium Battery

Tools Required

•

T-10 TORX driver (set to 9 in-lb)

•

T-20 TORX driver (set to 21 in-lb)

•

ESD grounding wrist strap

Removal Procedure

Refer to

Figure 7-37

for this procedure.

1. Disconnect the power cord.

2. Remove the A15 CPU board. Refer to

“Removing and Replacing the A15 CPU Board” on page 7-28

3. Lift the battery (item

①

) just enough to free it from its holder and slide it from under the battery clip (item

➁

). Be careful not to over bend the battery clip as it can be damaged or broken.

4. DO NOT THROW AWAY THE BATTERY. COLLECT IT AS SMALL CHEMICAL WASTE. Refer to

“Lithium

Battery Disposal” on page 1-9

for additional information on battery disposal.

Replacement Procedure

1. Reverse the order of the removal procedure following all instructions included with the new battery.

2. Perform the post-repair adjustments, verifications, and performance tests that pertain to this removal

procedure. Refer to

Table 7-2 on page 7-82

Summary of Contents for E8362C































































































































































































































































































































































































Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands

Agilent Technologies E8362C, Service Manual

Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands