Agilent Technologies E8362C Service Manual Download Page 306

Page: 306 / 382

7-50

Service Guide E8364-90038

Repair and Replacement Procedures

PNA Series Microwave Network Analyzers

Removing and Replacing the A25 and A26 Test Port Couplers

E8362C, E8363C, E8364C

Removing and Replacing the A25 and A26 Test Port Couplers

Tools Required

•

T-10 TORX driver (set to 9 in-lb)

•

T-20 TORX driver (set to 21 in-lb)

•

5/16-inch open-end torque wrench (set to 10 in-lb)

•

1-inch open-end torque wrench (set to 72 in-lb)

•

ESD grounding wrist strap

Removal Procedure

Refer to

Figure 7-22

for this procedure.

1. Disconnect the power cord.

2. Remove the outer cover. Refer to

“Removing the Covers” on page 7-6

. Position the analyzer bottom side

up and raise the receiver deck as shown. Refer to

“Raising and Removing the Receiver Deck” on page

7-8

if necessary.

3. Identify the test port coupler to be removed.

4. Remove the A43 or A44 receiver step attenuator, if present. This will allow access to the test port

couplers. Refer to

“Removing and Replacing the A43 and A44 35-dB Receiver Step Attenuators (Option

016)” on page 7-70

5. With a 5/16-inch torque wrench, disconnect the two semirigid cables (item

①

) from the test port

coupler.

6. With a 1-inch torque wrench, remove the test port coupler nut (item

➁

) from the front panel.

CAUTION

Be careful not to damage the center pins of the semirigid cables. Some flexing of the cables
is necessary to remove the assembly. Do not over-bend the semirigid cables.

7. Remove the test port coupler from the analyzer. Observe the

CAUTION

above.

Replacement Procedure

1. Reverse the order of the removal procedure.

2. Perform the post-repair adjustments, verifications, and performance tests that pertain to this removal

procedure. Refer to

Table 7-2 on page 7-82

Summary of Contents for E8362C































































































































































































































































































































































































Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands

Agilent Technologies E8362C, Service Manual

Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands