Agilent Technologies E8362C Service Manual Download Page 84 | Manualshive

Page: 84 / 382

background image

4-4

Service Guide E8364-90038

Troubleshooting

PNA Series Microwave Network Analyzers

Getting Started with Troubleshooting

E8362C, E8363C, E8364C

Getting Started with Troubleshooting

Where you begin troubleshooting depends upon the symptoms of the failure. Start by checking the basics as
outlined in the following section. Also review the flowchart in

Figure 4-1 on page 4-5

. You should then be

able to determine where in the troubleshooting procedure to begin, to locate the failed assembly.

Check the Basics

A problem can often be solved by repeating the procedure you were following when the problem occurred.
Before calling Agilent Technologies or returning the instrument for service, please perform the following
checks:

1.

Is there power at the mains receptacle? If not, correct this situation and proceed.

2.

Is the instrument turned on? Check to see if the front panel line switch glows. This indicates the power
supply is on. If the front panel line switch is on but the power supply does not appear to be on, go to

“Power Up Troubleshooting” on page 4-6

.

3.

Is the Windows

®

operating system running? If not, refer to

“Operating System Recovery”

in

Chapter 8

for instructions.

4.

If other equipment, cables, and connectors are being used with the instrument, make sure they are
clean, connected properly and operating correctly.

5.

If the PNA has Option 014, verify that the cables are connected properly.

6.

Review the procedure for the measurement being performed when the problem appeared. Are all the
settings correct? If not, correct them.

7.

If the instrument is not functioning as expected, return the unit to a known state by pressing the

Preset

key.

8.

Is the measurement being performed, and the results that are expected, within the specifications and
capabilities of the instrument? Refer to the embedded help in the analyzer for instrument specifications.

9.

If the problem is thought to be due to firmware, check to see if the instrument has the latest firmware
before starting the troubleshooting procedure. Refer to

“Firmware Upgrades”

in

Chapter 8

for

instructions.

10. If the necessary test equipment is available, perform the operator’s check and system verification in

Chapter 3, “Tests and Adjustments.”

«
...
82
83
84
85
86
...
»

Summary of Contents for E8362C































































































































































































































































































































































































Reviews:

No comments

Related manuals for E8362C

Brand: DAKOTA ULTRASONICS Pages: 48

Brand: TE Connectivity Pages: 9

Brand: M & I Instruments Pages: 2

Brand: Weller Pages: 9

Brand: jenway Pages: 52

Brand: Artesia Pages: 36

Brand: Bamo Pages: 17

Brand: Bruker BioSpin Pages: 76

Panametrics XDP

Brand: Baker Hughes Pages: 64

Brand: IROX Pages: 8

EA Heightmaster +

Brand: PROLEC Pages: 38

Brand: AccuLine Pages: 15

Brand: T&D Pages: 14

MRG 512 PQ Flex

Brand: janitza Pages: 9

Brand: Keithley Pages: 350

Brand: Panametrics Pages: 224

Brand: Micro-g LaCoste Pages: 168

Brand: Labom Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands