Agilent Technologies E8362C Service Manual Download Page 119 | Manualshive

Page: 119 / 382

background image

Service Guide E8364-90038

4- 39

PNA Series Microwave Network Analyzers

Troubleshooting

E8362C, E8363C, E8364C

Measurement System Troubleshooting

Checking Port 2 Power (B Signal)

The object of this check is to verify the power of the B signal across the entire frequency range. Perform this
test if there is an observed problem only with the channel B trace. The ten second sweep is slow enough to
allow you to observe the output power on the power meter as the sweep occurs.

1. Connect the power sensor to Port 2.

2. Observe the power reading on the power meter as the sweep occurs on the analyzer.

3. The measured output power on the power meter should be within -12 dBm ±4 dB for E836xB with no

options or -17 dBm ±4 dB for E836xB with options, over the entire frequency range.

Checking the Signal through the Signal Separation Path

For all of the following checks, refer to the block diagrams at the end of this chapter and to:

•

“Bottom Assemblies, No Options” on page 6-22

and

•

“Bottom Assemblies, Option UNL” on page 6-26

thru

“Bottom Semi-Rigid Cables, Options

UNL/014/016/080/081” on page 6-60

(as required)

Port 1 trace loss in the signal separation group is due to one or more of the following assemblies being
defective:

•

A22 switch splitter

•

A25 test port 1 coupler

•

A36 60-dB step attenuator (Option UNL)

•

A38 bias tee (Option UNL)

Port 2 trace loss in the signal separation group is due to one or more of the following assemblies being
defective:

•

A22 switch splitter

•

A26 test port 2 coupler

•

A37 60-dB step attenuator (Option UNL)

•

A39 bias tee (Option UNL)

Equipment Used for These Tests

To determine which assembly is defective, check the signal at each available measurement point in the
signal path from the A22 switch splitter to the test port coupler.

For Port 1 measurements, set the network analyzer for an S

11

measurement with a CW frequency of 1GHz.

For Port 2 measurements, set the network analyzer for an S

22

measurement with a CW frequency of 1 GHz.

Perform the following checks in the order presented.

Equipment Type

Models
Used With

Model or
Part Number

Alternate Model or Part
Number

Spectrum analyzer

All

8565E

856xE

1

1. Must be capable of measuring a signal at 1 GHz.

«
...
117
118
119
120
121
...
»

Summary of Contents for E8362C































































































































































































































































































































































































Reviews:

No comments

Related manuals for E8362C

Brand: Kane Pages: 16

Brand: Kane Pages: 60

Brand: TASKING Pages: 12

Brand: GARANT Pages: 368

Vortex Flow Industry

Brand: Grundfos Pages: 16

Brand: Spacelabs Pages: 156

Brand: Oldham Pages: 96

Brand: Leica Pages: 2

DIGIMET E30 Preset

Brand: MATO Pages: 20

Brand: Elcontrol Pages: 7

Brand: Vectronics Pages: 2

Brand: Resol Pages: 24

Brand: Bante Instruments Pages: 26

Brand: RX Pages: 8

Brand: Bartington Pages: 32

Brand: Alfano Pages: 47

ENSEMBLE GRANDE MARK 5

Brand: Kurzweil Pages: 32

Brand: Micro-g LaCoste Pages: 168

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands