Agilent Technologies E8362C Service Manual Download Page 138

Page: 138 / 382

5-2

Service Guide E8364-90038

Theory of Operation

PNA Series Microwave Network Analyzers

Information in This Chapter

E8362C, E8363C, E8364C

Information in This Chapter

This chapter provides a general description of the operating theory of the PNA series microwave network
analyzers.

•

Theory of operation is explained to the assembly level only.

•

Component-level circuit theory is not provided.

•

Simplified block diagrams are included for each functional group.

•

More detailed block diagrams are located at the end of

Chapter 4, “Troubleshooting.”

Chapter Five at-a-Glance

Section Title

Summary of Content

Start Page

Network Analyzer System Operation

A summary of the theory of operation for the analyzer.

A summary of the operation of the six functional groups
of the analyzer.

Page 5-3

Source Group Operation

Operation of the assemblies associated with the source
group.

Page 5-6

Signal Separation Group Operation

Operation of the assemblies associated with signal
separation, including the operation of Option 014.

Page 5-16

Receiver Group Operation

Operation of the assemblies associated with the receiver
group.

Page 5-21

Frequency Offset Group Operation
(Options 080 and 081)

Operation of the assemblies associated with frequency
offset mode of operation.

Page 5-24

IF Access Group (Option H11)

Operation of the assemblies associated with Option H11,
IF access.

Page 5-26

Digital Processing and Digital
Control Group Operation

Operation of the assemblies associated with digital
processing and control.

Page 5-28

Power Supply Group Operation

Operation of the power supply assembly group.

Page 5-33

Summary of Contents for E8362C































































































































































































































































































































































































Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands

Agilent Technologies E8362C, Service Manual

Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands