Agilent Technologies E8362C Service Manual Download Page 96

Page: 96 / 382

4-16

Service Guide E8364-90038

Troubleshooting

PNA Series Microwave Network Analyzers

Front Panel Troubleshooting

E8362C, E8363C, E8364C

Checking the USB Board

To verify proper operation of the USB board:

•

Connect a known good USB device, such as a USB mouse, to a front panel USB port.

•

Wait 15 seconds for the analyzer to verify the device connection, and then check the operation of the
USB device.

•

If the device performs correctly, the USB board is functioning properly.

•

If the device does not perform correctly, the USB board is faulty. Refer to

“Replacing the USB Connector

Board” on page 7-14

A3 Front Panel Interface Board

This assembly performs the following functions:

•

It routes USB signals between the front-panel USB connector and the A15 CPU board.

•

The speaker produces the audio output from signals supplied by the A15 CPU board.

•

It routes key pad commands from the keypad to the A15 CPU board.

•

It routes display signals from the A15 CPU board to the A2 display assembly.

Checking the Speaker

If no audio is heard:

•

Verify that the volume is set correctly and the proper sound driver is loaded; do the following:

— Press UTILITY

, then

•

Click on the

Sounds and Audio Devices

entry. Follow the normal Windows procedure to check the sound

drivers and volume. If the audio is still not heard, suspect a faulty speaker. Refer to

“Replacing the A3

Front Panel Interface Board” on page 7-14

Checking the Operation of the Key Pad Commands

To verify the key pad functionality, refer to

“Front Panel Keypad and RPG Test” on page 4-13

Checking the Display

To verify the display functionality, refer to

“A2 Display Test” on page 4-15

System

Configure

Control Panel

...

Summary of Contents for E8362C































































































































































































































































































































































































Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands

Agilent Technologies E8362C, Service Manual

Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands