manualshive.com logo in svg

Agilent Technologies E8362C, Service Manual

The Agilent Technologies E8362C is a cutting-edge device designed for accurate and efficient testing of electronic components. Discover all its features and functionalities by accessing the comprehensive Service Manual which can be freely downloaded from our website. Harness the power of this product and revolutionize your testing process.

Share
Download
background image

7-24

Service Guide E8364-90038

Repair and Replacement Procedures

PNA Series Microwave Network Analyzers

Removing and Replacing the A13 Frequency Offset Receiver Assembly

E8362C, E8363C, E8364C

Removing and Replacing the A13 Frequency Offset Receiver Assembly

Tools Required

•

T-10 TORX driver (set to 9 in-lb) 

•

T-20 TORX driver (set to 21 in-lb)

•

5/16-inch open-end torque wrench (set to 10 in-lb)

•

ESD grounding wrist strap

Removal Procedure

Refer to 

Figure 7-9

 for this procedure.

1. Disconnect the power cord.

2. Remove the outer and inner covers. Refer to 

“Removing the Covers” on page 7-6

.

3. With a 5/16-inch torque wrench, disconnect the three semirigid cables (item 

①

) and flexible cable (item 

➁

) from the top of the A13 frequency offset receiver assembly.

CAUTION

Be careful not to damage the center pins of the semirigid cables. Some flexing of the cables 
is necessary to remove the assembly. Do not over-bend the semirigid cables.

4. Disengage the A13 frequency offset receiver assembly from the A11 connector and slide out of the 

analyzer. Observe the 

CAUTION

 above.

Replacement Procedure

1. Reverse the order of the removal procedure.

2. Perform the post-repair adjustments, verifications, and performance tests that pertain to this removal 

procedure. Refer to 

Table 7-2 on page 7-82

. 

Summary of Contents for E8362C































































































































































































































































































































































































Reviews:

No comments

Related manuals for E8362C

Yamaha Mark III User Manual preview
Mark III
Brand: Yamaha Pages: 83
Yamaha Mark III Operating Manual preview
Mark III
Brand: Yamaha Pages: 63
S+S Regeltechnik HYGRASREG KH-30 Operating Instructions Manual preview
HYGRASREG KH-30
Brand: S+S Regeltechnik Pages: 16
Yamaha Clavinova CVP-601 Reference Manual preview
Clavinova CVP-601
Brand: Yamaha Pages: 98
Yamaha Electone CSY-1 Manual preview
Electone CSY-1
Brand: Yamaha Pages: 28
Shimpo DT209X Instruction Manual preview
DT209X
Brand: Shimpo Pages: 68
Velleman DVR8T3 Quick Installation Manual preview
DVR8T3
Brand: Velleman Pages: 107
Macnaught IM012E Instruction Manual preview
IM012E
Brand: Macnaught Pages: 8
BYK micro-TRI-gloss ? Operating Instructions Manual preview
micro-TRI-gloss ?
Brand: BYK Pages: 174
Agilent Technologies 16517A User Reference preview
16517A
Brand: Agilent Technologies Pages: 198
Parkside PZM 2 A1 Operation And Safety Notes preview
PZM 2 A1
Brand: Parkside Pages: 199
FuzzDog Quack Machine Quick Start Manual preview
Quack Machine
Brand: FuzzDog Pages: 6
Deprag 385484 A Operating Instruction Booklet preview
385484 A
Brand: Deprag Pages: 28
Kawai CN34 Software Update preview
CN34
Brand: Kawai Pages: 2
ABQ Industrial TotalCheck Owner'S Manual preview
TotalCheck
Brand: ABQ Industrial Pages: 32
Endress+Hauser Prosonic S FMU90 PROFIBUS DP Operating Instructions Manual preview
Prosonic S FMU90 PROFIBUS DP
Brand: Endress+Hauser Pages: 110
PowerMetrix PowerMaster MTA15Z Product Manual preview
PowerMaster MTA15Z
Brand: PowerMetrix Pages: 13
SARAD Radon Scout Home Manual preview
Radon Scout Home
Brand: SARAD Pages: 2

Brands by name

Popular brands

Load more brands