Agilent Technologies E8362C Service Manual Download Page 330

Page: 330 / 382

7-74

Service Guide E8364-90038

Repair and Replacement Procedures

PNA Series Microwave Network Analyzers

Removing and Replacing the A47 and A48 Couplers (Option H11)

E8362C, E8363C, E8364C

Removing and Replacing the A47 and A48 Couplers (Option H11)

Tools Required

•

T-10 TORX driver (set to 9 in-lb)

•

T-20 TORX driver (set to 21 in-lb)

•

5/16-inch open-end torque wrench (set to 10 in-lb)

•

ESD grounding wrist strap

Removal Procedure

Refer to

Figure 7-33

for this procedure.

1. Disconnect the power cord.

2. Remove the outer cover. Refer to

“Removing the Covers” on page 7-6

. Position the analyzer bottom side

up and raise the receiver deck as shown. Refer to

“Raising the Receiver Deck” on page 7-8

if necessary.

3. Locate the coupler to be removed; the A47 RF path coupler or the A48 LO path coupler. The A47 RF path

coupler is secured to the analyzer side frame (test set deck) and the A48 LO path coupler is secured to a
bracket which also holds the A19 splitter.

4. To remove the A47 RF path coupler:

a. With a 5/16-inch wrench, disconnect the three semirigid cables from the coupler.

CAUTION

Be careful not to damage the center pins of the semirigid cables. Some flexing of the cables
is necessary for removal. Do not over-bend them.

b. With a T-10 TORX driver, remove the mounting screws holding the coupler.

5. To remove the A48 LO path coupler:

a. With a 5/16-inch wrench, disconnect the three semirigid cables from the coupler and the three

semirigid cables from the A19 splitter.

b. With a T-10 TORX driver, remove the mounting screws from the bracket that holds the A48 LO path

coupler and the A19 splitter.

6. Remove the bracket, with the A48 LO path coupler attached, from the analyzer. Observe the

CAUTION

above.

7. Remove the A48 LO path coupler from the bracket by removing the attachment screws.

Replacement Procedure

1. Reverse the order of the removal procedure using the existing cables and hardware.

2. Perform the post-repair adjustments, verifications, and performance tests that pertain to this removal

procedure. Refer to

Table 7-2 on page 7-82

Summary of Contents for E8362C































































































































































































































































































































































































Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands

Agilent Technologies E8362C, Service Manual

Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands