manualshive.com logo in svg

Agilent Technologies E8362C, Service Manual

The Agilent Technologies E8362C is a cutting-edge device designed for accurate and efficient testing of electronic components. Discover all its features and functionalities by accessing the comprehensive Service Manual which can be freely downloaded from our website. Harness the power of this product and revolutionize your testing process.

Share
Download
background image

7-18

Service Guide E8364-90038

Repair and Replacement Procedures

PNA Series Microwave Network Analyzers

Removing and Replacing the A6, A8, A9, and A10 Boards

E8362C, E8363C, E8364C

Removing and Replacing the A6, A8, A9, and A10 Boards

Tools Required 

•

T-10 TORX driver (set to 9 in-lb) 

•

T-20 TORX driver (set to 21 in-lb)

•

ESD grounding wrist strap

Removal Procedure

Refer to 

Figure 7-7

 for this procedure.

1. Disconnect the power cord.

2. Remove the outer and inner covers. Refer to 

“Removing the Covers” on page 7-6

.

3. With a T-10 TORX driver, remove the two brackets that secure cables to the top of the midweb.

4. Identify the board you want to remove and disconnect any cables that are attached to it.

5. Lift the two extractors (item 

①

), located at each end of the board.

NOTE

Before removing the board completely, check the bottom of the board for any attached 
cables. 

6. While holding on to the extractors, slide the board out of the slot and remove it from the analyzer.

Replacement Procedure

1. Reverse the order of the removal procedure.

2. Perform the post-repair adjustments, verifications, and performance tests that pertain to this removal 

procedure. Refer to 

Table 7-2 on page 7-82

. 

Summary of Contents for E8362C































































































































































































































































































































































































Reviews:

No comments

Related manuals for E8362C

Kawai EP3 Owner'S Manual preview
EP3
Brand: Kawai Pages: 66
Yamaha Clavinova CLP-110 Bedienungsanleitung preview
Clavinova CLP-110
Brand: Yamaha Pages: 46
Yamaha Clavinova CLP-110 Mode D'Emploi preview
Clavinova CLP-110
Brand: Yamaha Pages: 46
Yamaha Arius YDP-S51 Reference Manual preview
Arius YDP-S51
Brand: Yamaha Pages: 8
AR Arrim ONE User Manual preview
Arrim ONE
Brand: AR Pages: 8
bmcm meM-INC Quick Start Manual preview
meM-INC
Brand: bmcm Pages: 5
Tektronix TAS 200 Instruction Manual preview
TAS 200
Brand: Tektronix Pages: 48
BYOGuitar.com JEM Assembly Instructions Manual preview
JEM
Brand: BYOGuitar.com Pages: 11
Siko IKM360R Quick Start Manual preview
IKM360R
Brand: Siko Pages: 2
ACE INSTRUMENTS AI-IAQ-SP-IoT Instruction Manual preview
AI-IAQ-SP-IoT
Brand: ACE INSTRUMENTS Pages: 6
Hameg HZ540 Manual preview
HZ540
Brand: Hameg Pages: 40
Sage RIO SIX Instruction Manual preview
RIO SIX
Brand: Sage Pages: 75
sewerin Multitec 520 Operating Instructions Manual preview
Multitec 520
Brand: sewerin Pages: 80
YOKOGAWA MG8E User Manual preview
MG8E
Brand: YOKOGAWA Pages: 63
Hanna Instruments HI 95771C Instruction Manual preview
HI 95771C
Brand: Hanna Instruments Pages: 12
YOKOGAWA WT310EH User Manual preview
WT310EH
Brand: YOKOGAWA Pages: 104
BC Biomedical USP-30 User Manual preview
USP-30
Brand: BC Biomedical Pages: 9
KERN MLS 50-3...N series Service Manual preview
MLS 50-3...N series
Brand: KERN Pages: 16

Brands by name

Popular brands

Load more brands