manualshive.com logo in svg

Acom eBox, User Manual, Page: 38 / 60

Share
Download
Acom eBox User Manual Download Page 38

User's Manual | ACOM eBox | Ethernet Remote Control Device  

Page  38 of 60  |  S e c t i o n   DEVICE AND AMPLIFIER SETTINGS 

 October 2021 

 

a)

 

Amplifier

 panel 

Please, see 

Figure 5-6 eBox with ACOM 700S connected

, Pos. (a). 

 
Panel functional buttons: 

•

 

OFF

 and 

ON

 

Switch the amplifier OFF or ON; 

•

 

Save 

When it is pressed the amplifier model change in a panel is saved; 

 
Panel functional fields: 

•

 

Model 

Allows  selection  of  connected  amplifier  model.  The  supported  models  are  ACOM  2000A, 
600S, 700S, and 1200S; 

•

 

State 

Displays  the  current  state  of  the  amplifier:  Starting,  Initializing,  Standby,  Powered  OFF,  or 
Operate; 

•

 

Serial 

Displays the amplifier serial number; 

•

 

FW, HW, Bootloader, Interface A, Interface B, and ATU Modem 

Displays the versions of firmware, hardware, bootloader, Interface A and B, and ATU modem; 

•

 

Hard faults 

Displays the number of stored hard faults in an amplifier memory. 

 
 
b)

 

User preferences 

panel

 

Please, see 

Figure 5-6 eBox with ACOM 700S connected

, Pos. (b). 

 
Th

е

 panel contains different user settings for the amplifier. 

 

For  details  about  your  ACOM  amplifier,  please,  read  corresponding  User's  Manual 
(Sections Menu CAT/AUX SETTINGS, and Menu USER PREFERENCES). 
The latest versions of our User's Manuals are available at 

www.acom-bg.com

. 

 
 
Panel functional buttons: 

•

 

Revert 

When it is pressed the change in the panel will go back to the last saved value; 

•

 

Save 

When it is pressed the changes in a panel are saved. 

 
Panel functional fields: 

•

 

Antenna Tuner 

Select  on  when  a  Remote  Automatic  Antenna  Tuner  and  Switch  ACOM  04AT  is  installed.  If 
there is no such device connected to the amplifier, error message will occur: 

(113) ATU/ASEL unassigned automatically and out of service; 

Summary of Contents for eBox





























































Reviews:

No comments