manualshive.com logo in svg

Acom eBox, User Manual, Page: 20 / 60

Share
Download
Acom eBox User Manual Download Page 20

User's Manual | ACOM eBox | Ethernet Remote Control Device  

Page  20 of 60  |  S e c t i o n   POWER ON AND INDICATORS 

 October 2021 

 

3.

 

POWER ON AND INDICATORS 

 

NOTICE 

Do not turn the eBox on for at least 30 minutes after unpacking it in the room where it 
will be used. Pay particular attention when you move  it from a very cold into a warm 
place - condensation is likely and this could result in damage to the device. 

 
 

NOTICE 

In  order  to  avoid  any  damage  (not  covered  by  the  warranty),  check  carefully  to  be 
certain that the voltage and power input plug of the eBox corresponds to your mains. 

 
 
After following all instructions in Section 

2 INSTALLATION

 you can insert the power supply adapter's mains 

plug to the wall outlet prepared for it. 
 
Once the device is powered the LED indicators (located on the eBox front panel) will blink a few times and 
5-10 seconds later the 

LAN

 and 

PWR

 indicators will remain green lit (see 

Figure 3-1 Front panel - Connection 

and indicators with power on).

 

 

Figure 3-1 Front panel - Connection and indicators with power on 

 

Figure 3-1 Front panel - Connection and indicators with power on 

 
 
The  meanings  of  six  LED  indicators  (see 

Figure  3-1  Front  panel  -  Connection  and  indicators  with  power  on

, 

Pos. (1)) on the front panel are as follow: 

•

 

LAN

 indicator 

Lights on: 

 

The device is connected to the LAN network; 

Lights blinking: 

 A user is logged-in (see Section 

4.2 Login and Authentication

); 

Lights off: 

 

The device is NOT connected to the LAN network; 

•

 

PWR

 indicator 

Lights on: 

 

The device is powered; 

Lights off: 

 

The device is NOT powered; 

•

 

REMOTE

 indicator 

Lights on: 

The ACOM amplifier is being controlled via eBox device; 

Lights off: 

 

The ACOM amplifier is NOT controlled via eBox device; 

1 

2 

Summary of Contents for eBox





























































Reviews:

No comments