Abbott Precision Xceed Pro Operator'S Manual Download Page 13

Page: 13 / 85

2-3

Questions? Refer to Page 10-10 for Technical Support Instructions.

Monitor Identification

Each monitor has a unique serial number listed on the back of the device just below the battery compartment. The

Precision Xceed Pro

Monitor also features an untextured area on the side of the device. This 22 mm wide x 11 mm

high (0.875 inch x 0.483 inch) area allows a facility to apply a label with information pertaining to the monitor.

Please refer to Chapter 1 for an illustration of this feature.

Menu Tree

When using the Precision Xceed Pro Monitor, you will navigate between two main menus, Test Mode and Menu

Mode. Test Mode is used to perform patient tests and control tests. Menu Mode is used to review data, perform

linearity and proficiency tests and review the monitor’s configuration settings and status (e.g. battery voltage).

The configuration options shown in Menu Mode must be configured using a data management system. You can

visually verify existing monitor settings, but cannot change them.

The Menu Mode portion of the software is set up like a tree, with various levels of sub-menus. The Precision

Xceed Pro Menu Tree, shown below, illustrates the multiple sub-menu layers.

Chapter 2: Using the Monitor

Summary of Contents for Precision Xceed Pro






















































































Search results

Summary of Contents for Precision Xceed Pro

Reviews:

Related manuals for Precision Xceed Pro

Brands by name

Popular brands

Abbott Precision Xceed Pro, Operator'S Manual

Search results

Summary of Contents for Precision Xceed Pro

Reviews:

Related manuals for Precision Xceed Pro

Brands by name

Popular brands