manualshive.com logo in svg

ABB DCS 500B, Description

The ABB DCS 500B, a versatile and reliable drive control system, enhances operational efficiency across industries. This product description provides an insight into its advanced features. Download the user manual for free from manualshive.com and explore the comprehensive instructions to maximize the potential of your DCS 500B.

Share
Download
background image

Functional Software description

                                                                                                                                                             

38

DCS 500 Software Description

Scaling of these limit values is 4095 = nominal current of the motor

I MOTN A (502)

ARM CURR LIM P (2307)

, scale: 4095 = I MOTN A (502)

ARM CURR LIM N (2308)

, scale: 4095 = I MOTN A (502)

Example.

 If the nominal current of the motor is 200A and the maximum

current is set to +/-230A, the limits are set to 230A/200A*4095=+/-4709.

Torque Limits

Torque limits for the speed controller and the external torque refer-
ence chain are set by means of the parameters. The program
takes care that these limits cannot exceed the final torque limits,
which are based on the given armature current limit and flux refer-
ence. This ensures that, e.g. the speed controller does not ask for
a larger torque than the current limits allow.
The torque limitation outputs 12301...12306 are internally con-
nected to torque reference chain and speed controller.

The armature current limits are calculated for the torque limits by
means of the flux reference in such a way that the nominal current
of the motor with nominal flux gives nominal torque of the motor,
scaling: 4000 = TN(motor). The final torque limits can be read out

from signals 

TORQMAX2 (12305)

 and 

TORQMIN2 (12306)

.

TORQ MIN (2306)

, scale: 4000==TN(motor)

TORQ MAX (2305)

, scale: 4000==TN(motor)

Speed Depend-
ant Current Limi-
tation

With the help of this function the load (motor´s shaft, coupling, gear
box and load machine) or the motor itself (commutation problems
at high speed) can be protected against overload.
If the drive is used in the field weakening range, the torque pro-
duced is lower than in the base speed range. Because of this and
together with the design criteria of the mechanics sometimes the
current needs to be lowered to avoid damage.
Some motors (most often at high speed motors) the current needs
to be reduced depending on the speed because of their electrical
design. Especially above the field weakening point the loading cur-
rent needs to be reduced according to instructions of motor cata-
logue.
The speed dependant current limitation function is described by 5
(x,y) coordinates. The pairs are:

1. 

… _LIM_SPEED

-

… _LIM_N1

2. 

point 1/4

-

… _LIM_N2

3. 

point 2/4

-

… _LIM_N3

4. 

point 3/4

-

… _LIM_N4

5. 

100% / 20000 point

-

… _LIM_N5

Linear interpolation is used for values between these coordinates.

Summary of Contents for DCS 500B





































































































































































































































Reviews:

No comments

Related manuals for DCS 500B

Uebo M400 Description & Operation preview
M400
Brand: Uebo Pages: 2
Samson 6111 Mounting And Operating Instructions preview
6111
Brand: Samson Pages: 28
MADRIX ORION Technical Manual & Quick Start Manual preview
ORION
Brand: MADRIX Pages: 36
Omega Engineering IP210 User Manual preview
IP210
Brand: Omega Engineering Pages: 10
Badger Meter HR-E LCD User Manual preview
HR-E LCD
Brand: Badger Meter Pages: 12
NAIM UNITISERVE-SSD - Reference Manual preview
UNITISERVE-SSD -
Brand: NAIM Pages: 27
Dynamix 10/100/1000 (SFP) User Manual preview
10/100/1000 (SFP)
Brand: Dynamix Pages: 2
Must 1012C User Manual preview
1012C
Brand: Must Pages: 10
Midmuro genio basic Installation Manual preview
genio basic
Brand: Midmuro Pages: 23
Optical Systems Design OSD2153 Series Operator'S Manual preview
OSD2153 Series
Brand: Optical Systems Design Pages: 20
SHOWTEC Node-1 Manual preview
Node-1
Brand: SHOWTEC Pages: 16
Tripp Lite PowerVerter RV Inverter/Charger RV1512UL Specifications preview
PowerVerter RV Inverter/Charger RV1512UL
Brand: Tripp Lite Pages: 5
Conceptronic CMED3PRO User Manual preview
CMED3PRO
Brand: Conceptronic Pages: 148
Esoteric Grandioso D1 Owner'S Manual preview
Grandioso D1
Brand: Esoteric Pages: 60
SDMC TMP-3T User Manual preview
TMP-3T
Brand: SDMC Pages: 31
AMS AS5245 Operation Manual preview
AS5245
Brand: AMS Pages: 11
tams elektronik 22-01-029 Manual preview
22-01-029
Brand: tams elektronik Pages: 39
National Instruments SCXI -1124 User Manual preview
SCXI -1124
Brand: National Instruments Pages: 54

Brands by name

Popular brands

Load more brands