manualshive.com logo in svg

ABB DCS 500B, Description

The ABB DCS 500B, a versatile and reliable drive control system, enhances operational efficiency across industries. This product description provides an insight into its advanced features. Download the user manual for free from manualshive.com and explore the comprehensive instructions to maximize the potential of your DCS 500B.

Share
Download
background image

Functional Software description

                                                                                                                                                                                  

DCS 500 Software Description

19

-

if 

STARTSEL (1717)

 = 1 (flying start):

the RUN command is no longer edge sensitive; the drive
will accelerate according to the reference, when the RUN
command is set to 1, independant, if the actual speed was
zero or different to zero before; if the drive was stopped by
the ON/OFF command (the RUN command was kept to
logic 1 level), it will react when ON/OFF changes from 0 to
1 in the same way, as if the RUN command would have
been used

- Coast Stop

When 

[COAST STOP] (905)

 input is set to logical state 1,

regulators are blocked and contactors remain closed. The drive
is allowed to decelerate freely towards zero speed. As long as
the drive stops in this way, the stop functions available with the
RUN command are disabled and vice versa.
This stop mode can be interrupted by Emergency Stop, Stop
because of panel or field bus link problems.

- Emergency Stop

If 

[EME STOP] (906)

 signal is set from 1 to 0, the emergency

stop function is activated. The reaction of the drive can be de-
fined by paramter 

EME STOP MODE (917)

 :

  0 = stop by ramp (

EMSTOP_RAMP (1714) 

) at

RAMP GENERATOR function block

  1 = stop by torque limit
  2 = coast stop (torque is zero)
  3 = dynamic brake
The state of the output signal 

EMESTOP ACT (10907) 

changes

0 -> 1. The drive will come up with an ALARM, which must be
reset and which will open all contactors at zero speed (with
coasting immediatelly).
For resetting the fault, see OPERATING INSTRUCTION
This stop mode can interrupt the Stop because of panel or field
bus link problems.

Summary of Contents for DCS 500B





































































































































































































































Reviews:

No comments

Related manuals for DCS 500B

Bang & Olufsen BeoSound Century User Manual preview
BeoSound Century
Brand: Bang & Olufsen Pages: 29
Unipower SLI 15 User Manual preview
SLI 15
Brand: Unipower Pages: 19
Cypress CDL-165ETHG Operation Manual preview
CDL-165ETHG
Brand: Cypress Pages: 24
FireBird CPK 7210 N Manual preview
CPK 7210 N
Brand: FireBird Pages: 44
Katana S610M User Manual preview
S610M
Brand: Katana Pages: 162
CMP PowerClean Salt Econ Installation Instructions & Product Manual preview
PowerClean Salt Econ
Brand: CMP Pages: 24
CYP AU-11SA-4K22 Operation Manual preview
AU-11SA-4K22
Brand: CYP Pages: 9
CTS MCT-2612 SERIES User Manual preview
MCT-2612 SERIES
Brand: CTS Pages: 2
Cablematic MM-SM Series User Manual preview
MM-SM Series
Brand: Cablematic Pages: 3
e+p UHD 18 Manual preview
UHD 18
Brand: e+p Pages: 2
Samlexpower SDC-23 Owner'S Manual preview
SDC-23
Brand: Samlexpower Pages: 3
CyberPower CPS150BURC1 User Manual preview
CPS150BURC1
Brand: CyberPower Pages: 1
UCEC USB 2.0 UVC Quick Start Manual preview
USB 2.0 UVC
Brand: UCEC Pages: 22
Duracell Inverter 3000 Installation Manual preview
Inverter 3000
Brand: Duracell Pages: 37
SHOWTEC Node-1 Manual preview
Node-1
Brand: SHOWTEC Pages: 16
Conceptronic CMED3PRO User Manual preview
CMED3PRO
Brand: Conceptronic Pages: 148
Esoteric Grandioso D1 Owner'S Manual preview
Grandioso D1
Brand: Esoteric Pages: 60
SDMC TMP-3T User Manual preview
TMP-3T
Brand: SDMC Pages: 31

Brands by name

Popular brands

Load more brands