3Com VCX V7111 User Manual Download Page 181 | Manualshive

Page: 181 / 464

background image

3Com

®

VCX V7111 VoIP Gateway User Guide

181

Parameter Description

RTP Base UDP Port

[BaseUDPPort]

Lower boundary of UDP port used for RTP, RTCP (Real-Time
Control Protocol) (RTP port + 1) and T.38 (RTP port + 2). The upper
boundary is the Base UDP Port + 10 * (number of gateways
channels).
The range of possible UDP ports is 6000 to 64000.
The default base UDP port is 6000.

For example:
If the Base UDP Port is set to 6000 (the default) then:
The first channel uses the following ports: RTP 6000, RTCP 6001
and T.38 6002,
the second channel uses: RTP 6010, RTCP 6011 and T.38 6012,
etc.

If RTP Base UDP Port is not a factor of 10, the following
message is generated: invalid local RTP port.
For detailed information on the default RTP/RTCP/T.38 port
allocation, see

Default RTP/RTCP/T.38 Port Allocation

.

Remote RTP Base UDP Port

[RemoteBaseUDPPort]

Determines the lower boundary of UDP ports used for RTP, RTCP
and T.38 by a remote gateway. If this parameter is set to a non-zero
value, ThroughPacket™ is enabled. Note that the value of
RemoteBaseUDPPort on the local gateway must equal the value of
BaseUDPPort of the remote gateway. The gateway uses these
parameters to identify and distribute the payloads from the received
multiplexed IP packet to the relevant channels.
The valid range is the range of possible UDP ports: 6000 to 64000.
The default value is 0 (ThroughPacket™ is disabled).

To enable ThroughPacket™ the parameters
L1L1ComplexTxUDPPort and L1L1ComplexRxUDPPort
must be set to a non-zero value.

RTP Multiplexing Local UDP Port

[L1L1ComplexTxUDPPort]

Determines the local UDP port used for outgoing multiplexed RTP
packets (applies to the ThroughPacket™ mechanism).
The valid range is the range of possible UDP ports: 4000 to 64000.
The default value is 0 (ThroughPacket™ is disabled).
This parameter cannot be changed on-the-fly and requires a
gateway reset.

RTP Multiplexing Remote UDP Port

[L1L1ComplexRxUDPPort]

Determines the remote UDP port the multiplexed RTP packets are
sent to, and the local UDP port used for incoming multiplexed RTP
packets (applies to the ThroughPacket™ mechanism).
The valid range is the range of possible UDP ports: 6000 to 64000.
The default value is 0 (ThroughPacket™ is disabled).
This parameter cannot be changed on-the-fly and requires a
gateway reset.

All gateways that participate in the same ThroughPacket™
session must use the same L1L1ComplexRxUDPPort.

«
...
179
180
181
182
183
...
»

Summary of Contents for VCX V7111

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7111

Brand: TempAlert Pages: 22

Brand: Foxconn Pages: 14

Brand: Sencore Pages: 37

Brand: PTT Pages: 21

lumos CONTROLS ENOR E

Brand: WiSilica Pages: 2

Brand: Festo Pages: 4

Brand: Festo Pages: 78

Brand: Bpt Pages: 25

Fieldgate SFG500

Brand: Endress+Hauser Pages: 52

Brand: Packet Power Pages: 2

Brand: Cradlepoint Pages: 148

Brand: Cabletime Pages: 16

Brand: AMSEC Pages: 73

Brand: Nateks Pages: 67

Brand: Danfoss Pages: 24

Brand: Lantronix Pages: 738

Brand: Vega Absolute Pages: 36

Brand: VegaStream Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands