3Com VCX V7111 User Manual Download Page 73

Page: 73 / 464

3Com

VCX V7111 VoIP Gateway User Guide

Parameter Description

SIP T1 Retransmission Timer [msec]

[

SipT1Rtx

]

The time interval (in msec) between the first transmission of a SIP
message and the first retransmission of the same message.
The default is 500.

The time interval between subsequent retransmissions of
the same SIP message starts with SipT1Rtx and is
multiplied by two until SipT2Rtx.

For example (assuming that SipT1Rtx = 500 and SipT2Rtx = 4000):
The first retransmission is sent after 500

msec.

The second

retransmission is sent after 1000 (2*500) msec

The third

retransmission is sent after 2000 (2*1000) msec

The fourth

retransmission and subsequent retransmissions

until

SIPMaxRtx

are sent after 4000 (2*2000) msec

SIP T2 Retransmission Timer [msec]

[

SipT2Rtx

]

The maximum interval (in msec) between retransmissions of SIP
messages. The default is 4000.

The time interval between subsequent retransmissions of
the same SIP message starts with SipT1Rtx and is
multiplied by two until SipT2Rtx.

SIP

Maximum

Rtx

[

SIPMaxRtx]

Number of UDP transmissions (first transm retransmissions)
of SIP messages.
The range is 1 to 7.
The default value is 7.

EnableReasonHeader

[Enable Reason Header]

Enables / disables the usage of the SIP Reason header.

[0]

= Disable.

[1]

= Enable (default).

Proxy & Registration Parameters

Use this screen to configure parameters that are associated with Proxy and Registration.

To configure the Proxy & Registration parameters:

Open the Proxy & Registration parameters screen (

Protocol Management

menu >

Protocol Definition

submenu >

Proxy & Registration

option); the Proxy & Registration

parameters screen is displayed.

Summary of Contents for VCX V7111

















































































































































































































































































































































































































































































Search results

Summary of Contents for VCX V7111

Reviews:

Brands by name

Popular brands

3Com VCX V7111, User Manual

Search results

Summary of Contents for VCX V7111

Reviews:

Brands by name

Popular brands