3Com Switch 4210 52-Port Configuration Manual Download Page 710

Page: 710 / 870

1-2

Implementation of VLAN-VPN

With the VLAN-VPN feature enabled, no matter whether or not a received packet already carries a

VLAN tag, the switch will tag the received packet with the default VLAN tag of the receiving port and add

the source MAC address to the MAC address table of the default VLAN. When a packet reaches a

VLAN-VPN-enabled port:

If the packet already carries a VLAN tag, the packet becomes a dual-tagged packet.

Otherwise, the packet becomes a packet carrying the default VLAN tag of the port.

VLAN-VPN Configuration

Enabling the VLAN-VPN Feature for a Port

Follow these steps to enable the VLAN-VPN feature for a port:

To do...

Use the command...

Remarks

Enter system view

system-view

—

Enter Ethernet port view

interface

interface-type

interface-number

—

Enable the VLAN-VPN feature
on the port

vlan-vpn enable

Required

By default, the VLAN-VPN
feature is disabled on a port.

Displaying and Maintaining VLAN-VPN Configuration

To do...

Use the command...

Remarks

Display the VLAN-VPN
configurations of all the ports

display port vlan-vpn

Available in any view

VLAN-VPN Configuration Example

Transmitting User Packets through a Tunnel in the Public Network by Using
VLAN-VPN

Network requirements

As shown in

Figure 1-3

, Switch A and Switch B are both Switch 4210 series switches. They connect the

users to the servers through the public network.

PC users and PC servers are in VLAN 100 created in the private network, while terminal users and

terminal servers are in VLAN 200, which is also created in the private network. The VLAN VPN

connection is established in VLAN 1040 of the public network.

Employ VLAN-VPN on Switch A and Switch B to enable the PC users and PC servers to

communicate with each through a VPN, and employ VLAN-VPN on Switch A and Switch B to

enable the Terminal users and Terminal servers to communicate with each other through a VPN.

Summary of Contents for Switch 4210 52-Port







































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Switch 4210 52-Port

Reviews:

Related manuals for Switch 4210 52-Port

Brands by name

Popular brands

3Com Switch 4210 52-Port, Configuration Manual

Search results

Summary of Contents for Switch 4210 52-Port

Reviews:

Related manuals for Switch 4210 52-Port

Brands by name

Popular brands