3Com Switch 4210 52-Port Configuration Manual Download Page 709

Page: 709 / 870

1-1

VLAN-VPN Configuration

When configuring VLAN-VPN, go to these sections for information you are interested in:

VLAN-VPN Overview

VLAN-VPN Configuration

Displaying and Maintaining VLAN-VPN Configuration

VLAN-VPN Configuration Example

VLAN-VPN Overview

Introduction to VLAN-VPN

Virtual private network (VPN) is a new technology that emerges with the expansion of the Internet. It can

be used for establishing private networks over the public network. With VPN, you can specify to process

packets on the client or the access end of the service provider in specific ways, establish dedicated

tunnels for user traffic on public network devices, and thus improve data security.

VLAN-VPN feature is a simple yet flexible Layer 2 tunneling technology. It tags private network packets

with outer VLAN tags, thus enabling the packets to be transmitted through the service providers’

backbone networks with both inner and outer VLAN tags. In public networks, packets of this type are

transmitted by their outer VLAN tags (that is, the VLAN tags of public networks), and the inner VLAN

tags are treated as part of the payload.

Figure 1-1

describes the structure of the packets with single-layer VLAN tags.

Figure 1-1

Structure of packets with single-layer VLAN tags

Figure 1-2

describes the structure of the packets with double-layer VLAN tags.

Figure 1-2

Structure of packets with double-layer VLAN tags

Compared with MPLS-based Layer 2 VPN, VLAN-VPN has the following features:

It provides Layer 2 VPN tunnels that are simpler.

VLAN-VPN can be implemented through manual configuration. That is, signaling protocol-related

configuration is not needed.

The VLAN-VPN feature provides you with the following benefits:

Saves public network VLAN ID resource.

You can have VLAN IDs of your own, which is independent of public network VLAN IDs.

Provides simple Layer 2 VPN solutions for small-sized MANs or intranets.

Summary of Contents for Switch 4210 52-Port







































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Switch 4210 52-Port

Reviews:

Related manuals for Switch 4210 52-Port

Brands by name

Popular brands

3Com Switch 4210 52-Port, Configuration Manual

Search results

Summary of Contents for Switch 4210 52-Port

Reviews:

Related manuals for Switch 4210 52-Port

Brands by name

Popular brands