3Com Switch 4210 52-Port Configuration Manual Download Page 647

Page: 647 / 870

1-14

Operation

Command

Description

SFTP server

[

-a

-l

] [

remote-path

]

If no file name is provided, all
the files in the current directory
are displayed.

The difference between these
two commands is that the

dir

command can display the file
name, directory as well as file
attributes; while the

command can display only the
file name and directory.

Download a remote file from
the SFTP server

get

remotefile

[

localfile

]

Upload a local file to the remote
SFTP server

put

localfile

[

remotefile

]

Rename a file on the remote
server

rename

remote

source

remote-dest

Optional

bye

exit

Exit SFTP client view and
return to system view

quit

The three commands have the
same effect.

Display the online help about a
specified command concerning
SFTP

help

[

all

command-name

]

Optional

If you specify to authenticate a client through public key on the server, the client needs to read the local

private key when logging in to the SFTP server. Since both RSA and DSA are available for public key

authentication, you need to use the

identity-key

key word to specify the algorithms to get correct local

private key; otherwise you will fail to log in. For details, see

SSH Operation Manual

SFTP Configuration Example

Network requirements

As shown in

Figure 1-6

, establish an SSH connection between the SFTP client (switch A) and the SFTP

server (switch B). Log in to switch B through switch A to manage and transmit files. An SFTP user with

the user name “client001” and password “abc” exists on the SFTP server.

Network diagram

Figure 1-6

Network diagram for SFTP configuration

VLAN-Int1
192.168.0.1/24

SwitchB

SFTP Server

SwitchA

SFTP Client

VLAN-Int1
192.168.0.2/24

Summary of Contents for Switch 4210 52-Port







































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Switch 4210 52-Port

Reviews:

Related manuals for Switch 4210 52-Port

Brands by name

Popular brands

3Com Switch 4210 52-Port, Configuration Manual

Search results

Summary of Contents for Switch 4210 52-Port

Reviews:

Related manuals for Switch 4210 52-Port

Brands by name

Popular brands