3Com NBX 100 Administrator'S Manual Download Page 437 | Manualshive

Page: 437 / 496

background image

Special Issues

437

You can use Microsoft’s VPN Dial Up Networking (version 1.3) to establish
a virtual private network connection between a roaming laptop and the
NBX system LAN. One end of the VPN connection is in the laptop while
the other end must be located in a VPN server between the router and
firewall.

The VPN server provides caller authentication and a secure (encrypted)
channel across the internet. After a caller has been authenticated, the
connection is passed to the firewall, which sees the VPN connection as
coming from a recognizable (and therefore firewall-configurable)
IP address. VPN allows a business person to establish an IP connection
into the NBX LAN from a hotel room with internet service.

After an Internet connection has been established, you must change your
automatic call forwarding number:

1

Log in to the NBX NetSet utility as a user.

2

On the

User Information

tab, click

Call Forward

.

3

Click the telephone number radio button.

4

Enter the number to which you want to forward the call and click

OK

.

The caller is now ready to use NetMeeting to place an H.323 to the NBX
system at the office. Configure NetMeeting with the IP address of the
ConneXtions gateway as the gateway in Advanced Calling options. Dial
the NBX extension to place the call.

The call passes through the Auto Attendant to your extension and
forwards the call to your previously specified number.

After the call, return to the NBX NetSet utility and remove the forwarded
number so that work-related calls to your extension are not forwarded to
your home, or to wherever you placed your last H.323 call.

PBX Connections

H.323 gateways allow NBX systems to establish IP connections to other
H.323-equipped PBXs as well as to similarly equipped NBX systems.
Although H.323 standards describe a universally accepted interface for
interconnecting similar systems, each of the 20 or 30 PBX manufacturers
brings its own PBX solution to the marketplace. This complexity is further
increased by the diversity of products and release levels that are
associated with each manufacturer. Because any implementation
differences can affect connectivity, this manual can only offer guidelines
for connecting NBX and PBX systems.

«
...
435
436
437
438
439
...
»

Summary of Contents for NBX 100

















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NBX 100

Brand: Safeline Pages: 76

Brand: Icom Pages: 2

Brand: Icom Pages: 326

UNIGATE MB EtherCAT

Brand: DEUTSCHMANN AUTOMATION Pages: 60

Brand: Rath Pages: 2

Brand: Intel Pages: 72

Brand: Carotron Pages: 20

Brand: Zte Pages: 22

Brand: Owon Pages: 12

Brand: Ness Pages: 7

Brand: 2Wire Pages: 132

Brand: ActionTec Pages: 147

Brand: ZyXEL Communications Pages: 361

Brand: Advantech Pages: 42

Brand: Hybertone Pages: 48

Brand: IDTECK Pages: 21

ISDN BRI GSM Enterprise

Brand: 2N Pages: 115

Brand: 3onedata Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands