3Com NBX 100 Administrator'S Manual Download Page 182 | Manualshive

Page: 182 / 496

background image

182

C

HAPTER

3: D

EVICE

C

ONFIGURATION

4

Type the new IP values for IP Address, Subnet Mask, and Default Gateway
address in the text boxes.

5

Click

OK

.

6

Unplug the device from the Call Processor subnetwork.

7

Connect the device to the new subnetwork as follows:

■

Connect a telephone or a single-port Analog Terminal Adapter to a
port on a switch or hub that is connected to the new subnetwork.

■

Plug a card into an NBX chassis that is connected to the new
subnetwork.

8

Reboot the device as follows:

■

Remove the power cord from a telephone or a single-port Analog
Terminal Adapter, and then reconnect it.

■

If the device is a card, it reboots automatically when you insert it into
the new chassis.

When you change IP Settings, all current calls through this device are
terminated.

9

In the NBX NetSet utility, return to the IP Settings dialog box for the
device.

10

Verify that the IP settings that you entered are now reported by the
device.

CAUTION:

If you have configured an NBX telephone for operation on a

subnetwork other than the Call Processor’s subnetwork, and if you access
the

Modify IP Settings

dialog box to verify that the device settings are

correct, you must exit the dialog box by clicking the

Cancel

button. If you

click

OK

, the NBX system applies the IP settings in the

Manually Assigned

IP Settings

text boxes. By default, all of these fields contain 0.0.0.0, and if

you click

OK

, all of the IP settings for the telephone are set to 0.0.0.0,

and the telephone no longer works on the “remote” subnetwork.

Configuring Call
Park

When you park a call, anyone can retrieve it from any other telephone in
the system by entering the Call Park extension that is associated with that
call.

Example:

You need to transfer an incoming caller, but the person

that you need to reach is not available. You can park the call on any
unused Call Park extension and then page the person, announcing the
Call Park extension where the call is parked. The person can then retrieve

«
...
180
181
182
183
184
...
»

Summary of Contents for NBX 100

















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NBX 100

NMEA CONNECT PLUS

Brand: Calypso Instruments Pages: 26

Brand: ICP DAS USA Pages: 7

Brand: ICP DAS USA Pages: 4

WILOW-IOT-GATEWAY-4G

Brand: BEANAIR Pages: 29

Brand: Datapulse Pages: 26

SecPath V1000-A

Brand: H3C Pages: 69

Brand: Dinstar Pages: 100

Fieldgate SWG70

Brand: WirelessHART Pages: 124

Brand: Cisco Pages: 10

Brand: Cisco Pages: 7

Brand: Cisco Pages: 19

Network Device MGX 8240

Brand: Cisco Pages: 2

Physical Access CIAC-GW-K9

Brand: Cisco Pages: 26

Brand: Cisco Pages: 60

Brand: Cisco Pages: 58

Brand: Cisco Pages: 29

Brand: Cisco Pages: 94

Brand: Cisco Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands