manualshive.com logo in svg

3Com 4007, Implementation Manual, Page: 283 / 684

Share
Download
3Com 4007 Implementation Manual Download Page 283

Protocol-based VLANs

283

2

Configure an IP routing interface with a network address and subnet 
mask and specify the interface type 

vlan

. 

3

Select the IP VLAN interface index that you want to

 bind

 to that IP 

interface.

If Layer 3 information is provided in the IP VLAN interface for which you 
are configuring an IP routing interface, the subnet portion of both 
addresses must be compatible. For example:

■

IP VLAN subnet 157.103.54.0 with subnet mask of 255.255.255.0

■

IP host interface address 157.103.54.254 with subnet mask of 
255.255.255.0

Layer 2 (bridging) communication is still possible within an IP VLAN (or 
router interface) for the group of ports within that IP VLAN. For allClosed 
VLANs, IP data destined for a different IP subnetwork uses the IP routing 
interface to reach that different subnetwork even if the destination 
subnetwork is on a shared port. For allOpen VLANs, using the destination 
MAC address in the frame causes the frame to be bridged; otherwise, it is 
routed in the same manner as for allClosed VLANs. 

4

Enable IP routing. 

You perform similar steps to create IPX and AppleTalk routing interfaces. 
For more information, see the chapters in this guide for routing protocols 
such as IP, IPX, and AppleTalk. 

Example 1: Routing Between Multilayer Modules 

The configuration in Figure 19 shows routing between Multilayer 
Switching Modules. (The switch fabric module resides in slot 7 but is 
logically represented above the other modules.) 

In this configuration:

■

There are two Multilayer Switching Modules and the switch fabric 
module.

■

There are four VLANs:

■

VLAN1, the default VLAN (tagged on backplane ports). The default 
VLAN is not represented in the figure. 

■

VLAN2, an IP VLAN that is defined on the Multilayer Switching 
Module in slot 3.

■

VLAN3, an IP VLAN that is defined on the backplane ports of both 
Multilayer Switching Modules and a port-based VLAN defined on 

Summary of Contents for 4007













































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments