manualshive.com logo in svg

3Com 4007, Implementation Manual, Page: 114 / 684

Share
Download
3Com 4007 Implementation Manual Download Page 114

114

C

HAPTER

 5: M

ANAGING

 

THE

 C

HASSIS

 P

OWER

 

AND

 T

EMPERATURE

Power

Non-Fault-Tolerant

Mode

Power non-fault-tolerant mode is:

■

A user-selectable mode in which 100 percent of the power that can be 
allocated to modules is available to them (no power is held in reserve).

■

The default mode for power supplies as shipped.

While the chassis is running in power non-fault-tolerant mode, the 
amount of power that is available to modules is determined only by the 
number of power supplies that are installed. If a power supply fails while 
the chassis is running in non-fault-tolerant mode:

■

Installed modules continue to operate without interruption if the 
output of the remaining power supplies is sufficient to provide 
adequate power to all installed modules.

■

The EME may shut down selected switch fabric modules and interface 
modules to bring installed module power consumption under the 
now-reduced power budget. See “Budgeting Power” on page 118 for 
more information about how the EME manages power.

Power Fault-Tolerant

Mode

Power fault-tolerant mode

 

is a user-selectable mode in which power that 

is equivalent to one power supply is held in reserve. This reserve power is 
not available to installed modules unless a power supply fails, or if you 
switch the power mode from power fault-tolerant mode to power 
non-fault-tolerant mode.

While the chassis is running in power fault-tolerant mode:

■

All installed power supplies are functioning and contributing power to 
the chassis and modules. No single power supply is a dedicated 
standby power supply. Rather, a factory-defined power limit ensures 
that power that is equivalent to at least one power supply is available 
to replace power lost if a power supply fails.

■

The amount of power that installed modules require must not be 
greater than the number of installed power supplies, minus one (n-1). 
When you reserve power that is equivalent to one power supply in 
power fault-tolerant mode, the failure of a single power supply has no 
impact on installed modules that are already powered on.

Summary of Contents for 4007













































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments