manualshive.com logo in svg

3Com 3036, Configuration Manual

The Casio 3036 is a multifunctional timepiece designed to cater to your every need. With its sleek design and advanced features, this watch is perfect for those seeking both style and functionality. Ensure you make the most of your Casio 3036 by downloading the free Operation Manual from manualshive.com.

Share
Download
background image

Configuring VRRP

655

Table 704   

Add Virtual IP Address

The standby group numbers ranges from 1 to 255. The virtual IP address should be 
the address of the network segment where the interface resides. It can be an 
unused IP address in the network segment, or the router's own IP address. When 
the virtual IP address is the router’s own IP address, this router is called an IP 
address owner. When the first IP address is added to a standby group, the system 
establishes this standby group. Whenever this command is executed after that, the 
system only adds this address to the virtual IP address list of this standby group. 
One router interface can be added into 14 standby groups at the same time, while 
one standby group can configure up to 16 virtual IP addresses. Before performing 
other configurations for one standby group, this command must be used first to 
establish this standby group.

Multiple virtual IP addresses (multiple virtual routers) can be configured in one 
standby group. All the virtual addresses take effect at the same time, and the 
computers in the LAN can choose any of the virtual routers as their gateway. The 

undo vrrp virtual-ip

 form of the command

 

can delete one existing standby 

group or delete one virtual IP address from the virtual address list on a standby 
group.

After the last virtual IP address has been deleted from the standby group, this 
standby group is also deleted. Then this standby group no longer exists on this 
interface and all the configurations of this standby group are no longer valid.

Configuring Router 

Priority in a Standby 

Group

The status of each router in a standby group can be determined by its priority in 
VRRP. The router with the highest priority becomes the master. Those with the 
same priority are judged by comparing the master IP addresses of their interfaces.

The range of priority is 0 to 255 (the bigger the number, the higher the priority) 
with 100 as the default. However the range to be configured is from 1 to 254. 
Priority 0 is reserved for special use by the system and 255 is reserved for the IP 
address owner.

Perform the following configuration in Ethernet interface view:

Table 705   

Configure Router Priority in Standby Group

The priority for IP address owners cannot be configured and it always remains 
255.

Operation

Command

Add Virtual IP Address

vrrp vrid 

virtual_router_id

 

virtual-ip 

ip-address

Delete virtual IP address

undo vrrp vrid 

virtual_router_id

 

virtual-ip [ 

ip-address

 ]

Operation

Command

Configure the priority of the standby 
group

vrrp vrid 

virtual_router_id

 priority 

priority

Restore the default value of the priority

undo vrrp vrid

 virtual_router_id

 

priority

Summary of Contents for 3036



























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3036

FOR-A MFR-16DTIO Installation Manual preview
MFR-16DTIO
Brand: FOR-A Pages: 2
Teac HD-35NAS User Manual preview
HD-35NAS
Brand: Teac Pages: 20
Maple Systems cMT-FHDX Series Installation Instruction preview
cMT-FHDX Series
Brand: Maple Systems Pages: 2
NETGEAR Powerline 100 Installation Manual preview
Powerline 100
Brand: NETGEAR Pages: 2
American Megatrends StorTrends 1312-P Specifications preview
StorTrends 1312-P
Brand: American Megatrends Pages: 2
Macsense MPC-200 User Manual preview
MPC-200
Brand: Macsense Pages: 13
red lion Yaskawa 2000 Information Sheet preview
Yaskawa 2000
Brand: red lion Pages: 5
AC&NC JetStor NAS 724UX User Manual preview
JetStor NAS 724UX
Brand: AC&NC Pages: 117
Zigen IP-Logic ZIG-IPPRO-RX Quick Start Manual preview
IP-Logic ZIG-IPPRO-RX
Brand: Zigen Pages: 4
NetCommWireless NTC-220 Series Quick Start Manual preview
NTC-220 Series
Brand: NetCommWireless Pages: 28
Allied Telesis AT-TN109-A Specifications preview
AT-TN109-A
Brand: Allied Telesis Pages: 2
Cambium Networks PMP/PTP 450 Series Quick Start Manual preview
PMP/PTP 450 Series
Brand: Cambium Networks Pages: 155
Cambium Networks PTP 250 User Manual preview
PTP 250
Brand: Cambium Networks Pages: 228
Cambium Networks PTP 550 Series User Manual preview
PTP 550 Series
Brand: Cambium Networks Pages: 249
Billion BiPAC 7404V series User Manual preview
BiPAC 7404V series
Brand: Billion Pages: 165
MikroTik RBM33G Quick Manual preview
RBM33G
Brand: MikroTik Pages: 9
Asus WL-167g deluxe User Manual preview
WL-167g deluxe
Brand: Asus Pages: 44
Asus 90IG02W1-BU9G10 User Manual preview
90IG02W1-BU9G10
Brand: Asus Pages: 67

Brands by name

Popular brands

Load more brands