Page 6-2
PREP Operation
NOTE: PREP takes approxim ately 1-1/2 hours.
If the Winchester disk does not contain i n i t i a l i z ation
i nformation ( f o r i n s t a n ce, th e d i s k m a y n o t h a v e
been initi al i zed or the i n f o r m a t ion may be in c o r rect
or damaged), PREP will p r o m p t yo u to enter charac-
teristics in o r der t o i d e n t if y t h e t y p e o f W i n c h e ster
d isk that is in the Compu t er. Then PREP will d i s p l a y
m essages that tell yo u w h a t i s h a p p en ing as it " p r e -
pares" and tests the disk.
CAUTION; Using PREP wil l d estroy all the fi les that
may exist on the W i n c h ester disk. W i n c h ester di sks
s upplied b y Z e n i t h D a t a S y s t em s C o r p o r atio n o r
Heath Company may have been prepared with PREP
a t the f actory , I f t h e d i s k h a s b ee n p r e p ared, y o u
w ill n eed t o u s e PREP only i f y o u c o n s i stently e n -
counter an u n r easonable nu m ber o f d i s k a c cess er-
r ors. Do not use PREP until yo u h ave backed up t h e
information on the Wi n c hester disk to floppy d i sk s.
T o run PREP, refer to Pictorial 6-1, and proceed wi t h
the follow in g di scussion.
•
R em ov e t h e W i n c h e s ter disk c o n t r o l l er c i r c u i t
board from the Z-100 card cage. You may have
to disconnect some cables to do this.
nectors.
turn it on.
Computer.
•
C onnect the l i n e c or d an d a p p l y p o w e r t o t h e
•
If t h e C o m p u t e r is a Low-Profile Mo d e l, be sure
t o connect th e m o n i t o r t o t h e C o m p u t e r a n d
•
R em o v e t h e j u m p e r f r o m i n t e r r u p t p l u g s 3 &
•
Plac e t he jumper over the format enable plugs
on the upper l eft corner of th e board (see inset
¹2),
•
Rep l a c e t h e b o a rd in t h e c a rd c age and r e con-
nect any cables that had to be d i sconnected to
remove the board. Make sure that all cables and
boards are full y seated in t h ei r r e spective con-
4 (see inset ¹1 ) w h ere it is normally stored.
•
In ser t t h e new ut i l i t i e s disk in dri ve 8.
•
B oot the f l o pp y d r i v e . N O T E : If th e C o m p u t e r
is configured to auto-boot from th e W i n c h ester
drive, you may have to press the DELETE key.
Содержание Z-100 Series
