manualshive.com logo in svg

York YDAJ87HU7, Руководство пользователя, Страница: 83 / 100

Поделиться
Скачать
York YDAJ87HU7 Скачать руководство пользователя страница 83

FORM 150.75-NM2

83

YORK INTERNATIONAL

for closer examination by factory service person-

nel is indicated.

H. If the oil is clean and free of metal particles, refill

the compressor with YORK oil “C”. To add oil or to

fill the compressor crankcase, connect the deliv-

ery tube of the YORK Hand Oil Pump. YORK Part

No. 470-10654 or equal to the compressor oil

charging and drain valve. Expel all air from the

delivery tube by pumping it full of oil, allowing a

few drips to drip out before tightening the flare nut

to the oil charging valve. Then open the oil charg-

ing valve and pump oil into the crankcase to the

proper level. It is necessary that the suction end

of the hand oil pump be kept submerged under

the oil level in the container at all times, to avoid

entrance of air into the compressor.

I. Before opening the suction or discharge stop

valves, connect a vacuum pump to the pump-out

port in the discharge stop valve. (Pump-out port is

port on valve stem side of valve). With the vacuum

line shutoff valve open, run the vacuum pump until

a vacuum of at least 1000 microns is reached.

Stop the vacuum pump, close the shut-off valve

and open the discharge valve fully before discon-

necting the line from the vacuum pump. Discon-

nect the vacuum pump and replace the plug in

the pump-out port.

NOTE: If suction or discharge valves are not seated

properly, a 1000 micron vacuum can not be ob-

tained. Do not evacuate for long periods of time.

J. Be sure both discharge and suction stop valves

are open before operating the unit.

4. Suction and Discharge Valves – The condition of the

suction and discharge valves should be checked by

YORK service personnel.

CONDENSER WATER PUMP CONTACT OPTION

This option provides a “dry” contact in the Master Panel

which can be used to turn on the condenser water pump,

other device or indicate run status. The contact closes

whenever one of the compressors start.

Connections to this contact can be made on Terminals

21 and 22 of TB1 in the power panel. The location of

these terminals is shown in Fig. 37.

This option utilizes a second Relay Output Board and

associated wiring. The part number for the Field

Mounted Pump Control Kit is 471-01232-101. This kit

is not required if a second Relay Output Board is al-

ready installed in the Master Panel.

FIG. 37 –

CONDENSER WATER PUMP CONTACT

CONNECTION POINT (

MASTER

 

PANEL

 

ONLY

)

OPTIONS

This section is devoted to options which may be ordered or retrofitted to the unit. Listed below are the options which

are covered in this section.

1. CONDENSER WATER PUMP/RUN STATUS CONTACT OPTION
2. EVAPORATOR WATER PUMP CONTACT OPTION
3. LOW AMBIENT ACCESSORY
4. HOT GAS BYPASS (LOADMINDER) OPTION
5. DISCHARGE PRESSURE READOUT OPTION
6. HIGH AMBIENT OPTION
7. LOCAL PRINTER OPTION
8. OPTIONAL TAMPERPROOF ENCLOSURE (WIRE GRILLE)
9. OPTIONAL DECORATIVE TAMPERPROOF ENCLOSURE (LOUVERED & WIRE GRILLE)

10. OPTIONAL DECORATIVE TAMPERPROOF ENCLOSURE (LOUVERED)

11. BAS INTERFACE OPTION (REMOTE RESET OPTION)

Both controls are included

as part of the

PUMP CONTROL KIT

LD01945

Содержание YDAJ87HU7





































































































Отзывы:

Нет отзывов