YASKAWA SLIO Скачать руководство пользователя страница 111

Страница: 111 / 116

4.12 Replace EtherCAT slave 053-1EC00 with 053-1EC01

It is not possible to copy modules and their properties / configuration from

EtherCAT Slave 053-1EC00 to EtherCAT Slave 053-1EC01 since the

EtherCAT slaves come from different ESI files.

When replacing an EtherCAT slave 053-1EC00 by 053-1EC01 an adaptation of your

project is required. When replacing the EtherCAT slaves, make sure that all settings and

parameters of the 053-1EC00 EtherCAT slave that deviate from the standard setting are

transferred to the EtherCAT slave 053-1EC01. Therefore, these settings should be saved

appropriately before the replacement. Precondition for replacing the EtherCAT slave

053-1EC00 by 053-1EC01 is that the ESI file for the EtherCAT slave 053-1EC01 is

installed in the configuration tool. The replacement takes place in the configuration by

deleting the EtherCAT slave 053-1EC00 and adding the EtherCAT slave 053-1EC01. In

the following all settings are listed, which should be noted.

EtherCAT station address
–

If the station address does not match that of the EtherCAT Slave 053-1EC00,

there is a topology error. The EtherCAT slave is not controlled.

Position of the EtherCAT slave on the bus
–

If the position of the EtherCAT slave on the bus does not match the position of the

EtherCAT slave 053-1EC00, there is a topology error. The EtherCAT slave is not

controlled.

Slot assignment of the modules
–

As long as the total IO size of the EtherCAT slave matches the configured size of

the master, the EtherCAT slave can switch to Operational (

). If the slot assign-

ment is changed, the wrong process data of the modules is transmitted

Download the slot configuration
–

If this option was activated for the EtherCAT slave 053-1EC00, then this option

should also be activated for the EtherCAT slave 053-1EC01. Please pay attention

to an identical slot assignment. If the slot configuration fits between master and

053-1EC01 but deviates from the slot configuration of EtherCAT slave

053-1EC00, this deviation is not recognized!

PDO mapping of the modules
–

For modules with variable IO size, for this modules the PDO mapping of the

053-1EC01 should be set exactly the same as for the 053-1EC00. Otherwise, the

slave does not change to

Safe-Op

CoE init commands
–

The CoE init commands at the 053-1EC01 should be made the same as with the

053-1EC00. If there are deviations, the EtherCAT slave can switch to

, but

there is a possibility that the EtherCAT slave or its modules will not behave as

expected.

Settings

System SLIO

Deployment

Replace EtherCAT slave 053-1EC00 with 053-1EC01

HB300 | IM | 053-1EC01 | en | 22-30

111

Содержание SLIO





















































































































Результаты поиска

Содержание SLIO

Отзывы:

YASKAWA SLIO, Руководство пользователя, Страница: 111 / 116

Результаты поиска

Содержание SLIO

Отзывы: