YASKAWA Lift Inverter L1000V, Техническое руководство

Страница: 231 / 282

B.3 Parameter Table
YASKAWA EUROPE SIEP YASKAWA AC Drive L1000V Technical Manual 231
Pa
ra
met
e
r Li
st
B
u
H: Multi-Function Terminals
H parameters assign functions to the multi-function input and output terminals.
n
H1: Multi-Function Digital Inputs
No.(Addr.) Name Description Setting Page
H1-03
(400H)
<19> With the speed reference priority d1-18 set to 0, the default settings for parameters H1-03 to H1-07 governing input terminals S3 to S7 are: 24,
13, 3, 4, and 5 respectively. When d1-18 is set to 1 or 2, the default settings for H1-03 to H1-07 become 50, 54, 51, 53, and F respectively.
Terminal S3 Function Selection
Assigns a function to the multi-function digital inputs.
Refer to page
231 to page 232 for a description of setting values.
Note: Unused terminals should be set to F.
Default:
<19>
Min: 3
Max: 79 124
H1-04
(401H)
Terminal S4 Function Selection
Default:
<19>
Min: 3
Max: 79 124
H1-05
(402H)
Terminal S5 Function Selection
Default:
<19>
Min: 3
Max: 79 124
H1-06
(403H)
Terminal S6 Function Selection
Default:
<19>
Min: 3
Max: 79 124
H1-07
(404H)
Terminal S7 Function Selection
Default:
<19>
Min: 3
Max: 79 124
H1 Multi-Function Digital Input Settings
H1-
Setting
Function Description Page
3 Multi-Step Speed Reference 1
When input terminals are set to Multi-Step Speed References 1 through 3, switching combinations of those
terminals will create a multi-step speed sequence using the speed references set in d1-01 through d1-08.
124
4 Multi-Step Speed Reference 2 124
5 Multi-Step Speed Reference 3 124
7 Accel/decel Ramp Selection 1 Used to switch between accel/decel ramp 1 (set in C1-01, C1-02) and accel/decel ramp 2 (set in C1-03, C1-04).
When combined with another input terminal set for "Accel/Decel ramp 2" (H1-
= 1A), the drive can also
switch between accel/decel ramp 3 (set in C1-05, C1-06) and accel/decel ramp 4 (set in C1-07, C1-08).
124
8 Baseblock Command (N.O.)
Closed: No drive output
124
9 Baseblock Command (N.C.)
Open: No drive output
124
F Not Used (Through Mode)
Select this setting when using the terminal in a pass-through mode. The terminal does not trigger a drive function
but can be used as digital input for the controller the drive is connected to.
124
14 Fault Reset
Closed: Resets faults if the cause is cleared and the Up/Down command is removed.
125
15 Emergency Stop (N.O.)
Closed: Decelerates to stop at the Emergency Stop ramp set to C1-09.
125
17 Emergency Stop (N.C.)
Open: Decelerates to stop at the Emergency Stop ramp set to C1-09.
125
18 Timer Function Input
Triggers the timer set up by parameters b4-01 and b4-02. Must be set in conjunction with the timer function output
(H2-
= 12).
125
1A Accel/decel Ramp Selection 2
Used in conjunction with an input terminal set for “Accel/decel ramp selection 1” (H1- = 7), and allows the
drive to switch between accel/decel ramp 3 and 4.
125
All Modes
common_
TMonly
All Modes
common_
TMonly
All Modes
common_
TMonly
All Modes
common_
TMonly
All Modes
common_
TMonly
All Modes
common_
TMonly
All Modes
common_
TMonly
All Modes
common_
TMonly
All Modes
common_
TMonly
All Modes
common_
TMonly
All Modes
common_
TMonly