Yamaha RX10RL страница 90 Скачать руководство пользователя

Страница: 90 / 99

9-3

8. Start the engine.
9. Disconnect the black (-) jumper cable

from the black (-) connecting lead, and
then pull the cover completely over the
lead terminal.

10. Disconnect the black (-) jumper cable

from the negative (-) terminal of the
booster battery.

11. Disconnect the red (+) jumper cable

from the positive (+) terminal of the
booster battery.

12. Disconnect the red (+) jumper cable

from the red (+) connecting lead, and
then pull the cover completely over the
lead terminal.

13. Install the red (+) connecting lead into

the lead holder.

14. Install the right side cover and the

shroud.

WARNING

Be sure to pull the lead covers back
over the terminals completely. If the ter-
minals are exposed, they could come
into contact with the frame or a metal
part of the snowmobile and this can
cause electrical system damage or A
FIRE HAZARD.

NOTE:

Make sure that both the red (+) connecting
lead and the black (-) connecting lead are
seated securely in the lead holders.

C. Electric starter does not operate or

operates slowly

1. Engine stop switch is pushed in ... Pull

it out.

2. Faulty wire connections ... Check con-

nections or ask a Yamaha dealer to
inspect.

3. Discharged battery... Charge battery or

see B above.

4. Seized engine ... Seizure is caused by

poor lubrication, inadequate fuel, or an
air leak—Ask a Yamaha dealer to
inspect.

D. Engine power is low

1. Low coolant temperature indicator light

is flashing ... Warm the engine up.

2. Faulty spark plugs ... Clean or replace

the spark plugs.

3. Improper fuel flow ... See A.1. above.
4. Incorrect V-belt clutch settings for alti-

tude or conditions ... Ask a Yamaha
dealer to inspect.

E. Engine constantly backfires or mis-

fires

1. Faulty spark plugs ... Replace the

spark plugs.

2. Clogged fuel system ... See A.1. above.
3. Malfunctioning T.O.R.S. ... See A.2.

above.

F. Engine overheats

1. Insufficient coolant ... Add coolant.
2. Air in cooling system ... Bleed the cool-

ing system or ask a Yamaha dealer to
inspect.

3. Leaking coolant ... Ask a Yamaha

dealer to inspect.

G. Snowmobile does not move

1. Malfunctioning V-belt clutch ... Ask a

Yamaha dealer to inspect.

2. Drive track does not move ... Foreign

object is caught in the drive track, or
slide runners have melted to the slide
metal due to lack of lubrication.

3. Tight, loose, or broken drive chain ...

Ask a Yamaha dealer to inspect.

U8FP10.book Page 3 Thursday, April 28, 2005 5:11 PM

Содержание RX10RL




































































































Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды

Yamaha RX10RL, Руководство пользователя

Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды