Yamaha RX10RL Скачать руководство пользователя

Страница: 30 / 99

5-11

ESU04130

Rear suspension damping force remote adjust-
ment dial

Turn the remote adjustment dial to adjust the rear sus-
pension damping force. (See page 8-25 for adjustment
procedures.)

Rear suspension damping force remote adjustment
dial

ESU00039

Headlight beam switch

Push the headlight beam switch to change the headlight
beam to high or low.

Headlight beam switch

Push

High beam

Low beam

ESU04301

Auxiliary DC jack

The auxiliary DC jack is located in the front panel and
can be used for accessories.

NOTE:

The auxiliary DC jack cannot be used if the engine is not
running.

1. Start the engine.
2. Open the auxiliary DC jack cap

, and then insert

the accessory power plug into the jack

NOTE:

After using the auxiliary DC jack, be sure to remove the
accessory power plug from the jack and close the auxil-
iary DC jack cap.

U8FP10.book Page 11 Thursday, April 28, 2005 5:11 PM

Содержание RX10RL




































































































Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды

Yamaha RX10RL, Руководство пользователя

Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды