background image

8-25

ESU04693 

Adjusting the rear suspension damping force

The damping force can be adjusted by turning the rear
suspension damping force remote adjustment dial in
direction 

a

 “HARD” or direction 

b

 “SOFT”.

1

Rear suspension damping force remote adjustment
dial 

2

Standard position

WARNING

Do not turn the remote adjustment dial while the
snowmobile is moving as this could cause loss of
control, an accident, and injury. 

@

CD-25E

CAUTION:

Be sure to stop the remote adjustment dial at a
marked position around the dial where there is a
click. 

@

WARNING

This shock absorber contains highly pressurized
nitrogen gas. It could explode by improper handling,
causing injury, or property damage. 

Do not tamper with or attempt to open the shock
absorber. 

Do not subject the shock absorber to an open
flame or other high heat source, which could
cause it to explode. 

Do not deform or damage the shock absorber in
any way. 

Do not dispose of a worn or damaged shock
absorber by yourself. Take the unit to a Yamaha
dealer. 

Dial position

Direction 

b

Direction 

a

Damping force

Soft

Hard

11 clicks

 “MAX SOFT”

Standard

11 clicks

“MAX HARD”

U8FP10.book  Page 25  Thursday, April 28, 2005  5:11 PM

Содержание RX10RL




































































































Отзывы: