Yamaha RX10RL Скачать руководство пользователя | Manualshive

Страница: 69 / 99

background image

8-16

4. Start the engine, allow it to idle for several minutes,

and then turn it off.

5. Check the coolant reservoir. If it is not full, remove the

coolant reservoir cap, fill the reservoir with the recom-
mended coolant, and then install the cap.

6. Check for any coolant leakage.

NOTE:

@

If you find any leaks, consult a Yamaha dealer.

@

7. Install the top cover.

ESU04550

Replacing the V-belt

WARNING

@

When installing the new V-belt, make sure it is posi-
tioned from 1.5 mm (0.06 in) above the edge of the
secondary sheave assembly to 0.5 mm (0.02 in)
below the edge

a

.

If not, the V-belt clutch engagement speed will be
changed. The snowmobile may move unexpectedly
when the engine is started.
Adjust the V-belt position by removing or adding a
spacer

1

on each adjusting bolt.

Have a Yamaha dealer make this adjustment.

@

CAUTION:

@

As the V-belt wears, adjustment may be necessary.
To ensure proper clutch performance, the V-belt
position should be adjusted by adding a spacer on
each adjusting bolt when the V-belt position reaches
1.5 mm (0.06 in) below the edge.
Have a Yamaha dealer make this adjustment.

@

CD-05E

NOTE:

@

Apply the parking brake before replacing the V-belt.

@

New belt width

34.5 mm (1.36 in)

Belt wear limit width

32.5 mm (1.28 in)

U8FP10.book Page 16 Thursday, April 28, 2005 5:11 PM

«
...
67
68
69
70
71
...
»

Содержание RX10RL




































































































Отзывы:

Нет отзывов

Похожие инструкции для RX10RL

800 PRO-RMK 2011

Бренд: Polaris Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды