Yamaha RX10RL страница 29 Скачать руководство пользователя

Страница: 29 / 99

5-10

ESU00035

Parking brake lever

When parking the snowmobile or starting the engine,
apply the parking brake by moving the brake lever

the left.
To release the parking brake, move the parking brake
lever

to the right.

To apply the parking brake

To release the parking brake

WARNING

●

Always set the parking brake before attempting to
start the engine.

●

Never run the snowmobile with the parking brake
applied. This may overheat the brake disc and
reduce braking ability.

ESU00341

Shift lever

For RX10R/RX10RTR/RXW10

The shift lever is used to put the snowmobile into forward
or reverse. After coming to a complete stop, pull the shift
lever out, slide it to “FWD” or to “REV” until it stops, and
then release it.

Shift lever

Pull out

Slide to “FWD” (Forward)

Slide to “REV” (Reverse)

Release

CAUTION:

Do not shift from “FWD” to “REV” or from “REV” to
“FWD” while the snowmobile is moving. Otherwise,
the drive system could be damaged.

U8FP10.book Page 10 Thursday, April 28, 2005 5:11 PM

Содержание RX10RL




































































































Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды

Yamaha RX10RL, Руководство пользователя

Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды