Yamaha RX10RL Скачать руководство пользователя

Страница: 42 / 99

6-10

ESU04601

Air filter

Always check that there is no snow under the air filter
element frame.

1. Remove the shroud. (See pages 8-5–8-7 for removal

procedures.)

2. Unhook the air filter case cover fasteners.
3. Remove the headlight unit bolts and the two top

cover bolts near the headlight unit.

4. Slightly lift up the headlight unit, and then remove the

air filter case cover.

5. Lift up the air filter element frame and check the air

filter element. If there is any snow on the air filter ele-
ment, remove the element and brush off the snow,
and then install the air filter element.

6. Place the air filter element frame in its original posi-

tion, and then install the air filter case cover. Hook the
fasteners onto the air filter case cover.

7. Install the headlight unit, making sure to insert the

tabs on the headlight unit stay into the slots on the
bottom of the headlight unit.

8. Install the headlight unit bolts, and then tighten them

to the specified torque.

9. Install the top cover bolts.

10. Install the shroud.

NOTE:

After riding the snowmobile, make sure that there is no
snow under the air filter element frame.

Headlight unit bolt tightening torque:

3 Nm (0.3 m·kgf, 2.2 ft·lb)

U8FP10.book Page 10 Thursday, April 28, 2005 5:11 PM

Содержание RX10RL




































































































Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды

Yamaha RX10RL, Руководство пользователя

Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды